A.
Where shown on the plans, portland cement concrete curbs shall be constructed on both sides of the street to the dimensions and specifications shown on Figure VII-1.
B.
Where required by the Highway Superintendent or the Town Engineer, perforated polymeric or aluminum coated corrugated metal pipe, or perforated polyethylene corrugated pipe with a minimum diameter of six inches shall be laid as shown on Figure VI-2. This underdrain shall be graded so that any water under the curbs will drain to the nearest catch basin where the underdrain shall be connected as shown an Figure V-1.
C.
Concrete shall be finished and cured to the satisfaction
of the Highway Superintendent or the Town Engineer. The developer
shall, at his own expense, replace any curbing damaged before dedication.
D.
All rural/suburban highways shall have asphalt cement concrete curbs of the construction shown in Figure VII-1. The curb shall be set on the binder course of pavement. The Highway Superintendent shall have the discretion to waive the requirements of curbs on any portions of a rural/suburban road where he deems it appropriate. The developer shall, at his own expense, replace any asphalt curbing damaged before roadway dedication. All driveway entrances within the subdivision shall be constructed at the time of construction of the curb.
E.
Curbs may be mountable or nonmountable type, as shown
on the plan. Curbs on medians, inside shoulder edges or outlining
channelizing island shall typically be nonmountable type.
F.
Ramps for the handicapped, required by § 330
of the Highway Law, shall be provided at each curbed intersection
and midblock crosswalks where curbs are constructed. Ramps at intersections
shall be constructed in accordance with Figures VII-2 and VII-3, and
the specifications for sidewalks. Ramps at midblock locations shall
be constructed in a similar manner.
G.
Topsoil shall be placed behind newly constructed curbs.
The topsoil shall be placed two inches higher than the face of curb,
or continuously refilled, to ensure that the sod is flush with the
top of the curb. No pockets or settlement shall be permitted. Any
low spots shall be filled, seeded and mulched as required by the Highway
Superintendent or the Town Engineer.
A.
Sidewalks may be required on any cul-de-sac less than
1/2 mile long. The sidewalk shall wrap around the cul-de-sac on the
side to maximize exposure to the winter sun.
B.
Sidewalks may be constructed of portland cement or
asphalt cement concrete, except that asphalt cement concrete sidewalks
may only be constructed in residential areas.
C.
Portland cement concrete shall be New York State Department
of Transportation Class A with air entrainment of 6% by volume.
D.
Bituminous material shall meet the requirements of
Type 1AC or 1ACF of Section 401 of the current New York State Department
of Transportation Standard Specifications.
E.
Where shown on the plans, the developer shall construct sidewalks in accordance with Figure II-2 and Figure VII-2a, VII-2b, VII-3, VII-4A, VII4-B and VII4-C.
[Amended 11-14-2002 by L.L. No. 5-2002]
(1)
Portland cement concrete sidewalk shall be minimum
six inches thick.
(2)
Asphalt cement concrete sidewalk shall be constructed
in two lifts. A four-inch binder course and a two-inch wearing course
shall be constructed in accordance with the specifications for streets,
except that the requirements for size and type of roller shall not
apply.
A.
Permanent monuments may be required on the right-of-way
line of a roadway at all road intersections, angle points, points
of curve, subdivision corners, easements and other locations as directed
by the Highway Superintendent or the Town Engineer.
B.
Monuments shall be cut granite, free from imperfections, or concrete, and as shown on Figure VII-5. Iron pipes, unless embedded in concrete, shall not be considered permanent monuments for the purpose of this specification.
C.
Monuments shall not be set until the roadway has been
completed, nor shall they be set while frost is in the ground. They
shall be set and tamped to prevent settlement, shifting or movement.
Monuments shall be set so that they cannot be easily removed, if necessary
by encasing the lower half in a concrete anchor (similar to a fence
or sign post).
D.
The developer's licensed land surveyor shall certify
that the location of all monuments is accurate, before acceptance
of the highway by the Town Board, and all monument locations shall
be shown on the as-built drawings (plans).
A.
The type and need for guiderail installation shall
be approved by the Highway Superintendent and the Town Engineer. All
guiderail installations shall be designed in accordance with Guiderail
II, or latest revision, published by the New York State Department
of Transportation Traffic Safety Division.
B.
The primary warrants to determine the need for guiderail
are:
(1)
Height of drop-off (measured from the break
of shoulder slope to the toe of slope) compared to the rate of embankment
slope. Guiderail is not warranted unless the geometry of the features
involved exceed the criteria below:
Slope (H:V)
|
Embankment Height
| |
---|---|---|
2 to 1
|
6 feet
| |
3 to 1 or flatter
|
Guiderail not required
|
It is also assumed in the above geometrical
consideration that the toe of slope conditions are such that no abrupt
dropoffs or adverse slopes forming "V" ditches will be encountered.
|
(2)
Guiderails shall be installed to protect motorists
from fixed objects and roadside hazards as shown on the following
list:
Culvert headwalls.
| |
Along bodies of water over two feet deep.
| |
Rock cuts and rock outcrops.
| |
Retaining walls.
| |
Any other immovable object as determined by
the Highway Superintendent.
|
C.
Guiderail installation shall be in accordance with
Sections 710-20, Corrugated Beam Guide Railing, and 710-21 Box Beam
Guide Railing, of the current Standard Specifications of the New York
Department of Transportation (see Figures VII-6 and 7).
A.
All signs, signals, markings and other control devices
for maintenance and protection of traffic and for naming roads shall
conform to the requirements of the New York State Manual of Uniform
Traffic Control Devices.
B.
The developer shall install a stop sign at the intersection of a new road with an existing Town, county or state road and at intersections within the subdivision itself as determined by the Highway Superintendent or the Town Engineer. The developer shall furnish and install a four-way road name sign at every road intersection made by the roads he constructs. See Figure VII-8. The developer may also be required to install other signs, such as W7-4 Children at Play, as determined by the Highway Superintendent or the Town Engineer.
Roof, cellar, trench, curtain, footing or any
other house drain or septic system drain shall in no case be allowed
to flow onto the highway right-of-way. With the approval of the Highway
Superintendent and the Town Engineer, in writing, these drains may
be piped to the roadway and they shall be connected to a catch basin
or to the top of a pipe only. Such drains must be installed prior
to the start of the application of the roadway foundation course.
B.
Design.
(1)
Driveways shall be designed similar to a road intersection. A driveway center line shall be offset from a road intersection center line a minimum of 125 feet. Driveways entering onto a minor local road may be no closer than 45 feet to the stop sign cross bar at an intersection. Driveways shall have adequate sight distance (see § A197-27.).
[Amended 11-14-2002 by L.L. No. 5-2002]
(2)
A separate driveway shall be required for each lot, unless the Planning Board has approved a shared driveway in accordance with § 194-67.1.
[Amended 11-14-2002 by L.L. No. 9-2002]
(3)
The minimum pavement or gravel width for driveways
shall be 12 feet. The minimum overhead clearance shall be 12 feet.
(4)
Driveway grades for that portion of the driveway
within the right-of-way of a highway or street shall conform to the
profile of the existing pavement. Driveway grades shall not exceed
a gradient of 4% within 30 feet of the roadway, then 15% overall,
then 4% within 30 feet of the dwelling. Changes in driveway grades
beyond the highway, street right-of-way, or structure shall not exceed
8% per 10 feet, and the maximum grade shall not exceed 15%. Where
elevations are sought, the developer shall submit driveway profiles,
grading plan and cross sections to permit a technical evaluation of
the proposal by the Building Inspector and the Town Engineer.
[Amended 10-28-2010 by L.L. No. 6-2010]
(5)
The driveway entrance, curbing, gutter, drainage
ditch and roadway interference shall be designed:
(6)
All positive grade driveways shall continue
at positive grade to the edge of pavement of the road to prevent ponding.
(7)
Driveways shall be designed to provide Fire
Department apparatus access to within a distance of 150 feet or less
of the structure it may be called upon to protect. No turn shall be
of such a degree as to prevent access of Fire Department apparatus.
(8)
Driveways shall be able to support a thirty-ton,
three-axle apparatus.
C.
Construction.
(1)
All driveways in excess of 3% shall be paved their entire length, all others shall be paved for the first 30 feet (apron) from the edge of pavement. Paving requirements shall be in accordance with Figure VII-10.
(2)
For driveways constructed in wet areas, all
unsuitable material shall be excavated and replaced with suitable
material. Curtain drains should be installed which discharge into
the roadway storm drain system.
A.
Where required by the Highway Superintendent or a county or state work permit, a twelve-inch stop bar shall be painted on the pavement. See Figure VII-10.
B.
All pavement markings (including lane stripes, edge
lines, arrows and words) shall be made with thermoplastic paint conforming
to current New York State Department of Transportation Specifications.
White or yellow markings shall be made in accordance with the MUTCD
requirements for size, shape and color code. The locations of all
markings shall be shown on a site plan and approved by the Highway
Superintendent or the Town Engineer.
A.
The specific requirements shall be established by
the Highway Superintendent and the Town Engineer.
B.
In general, the structure shall be designed for an
HL-93 design loading. Clearance to another roadway shall be minimum
16 feet. The waterway opening shall be designed to pass a one-hundred-year
storm.
[Amended 6-22-2017 by L.L. No. 2-2017]
If it becomes necessary to close a road or a
lane, the developer shall furnish a detour or lane closure plan for
approval by the Highway Superintendent. The recommendations of the
MUTCD shall be followed.