The jurisdiction of this chapter shall include all lands and
waters within the Town of Ledgeview.
A.
Restrictions or requirements with respect to buildings or land, or
both, which appear in other ordinances of the Town of Ledgeview or
are established by federal, state or county laws and which are greater
than those set forth herein shall take precedence over those herein.
Otherwise, the provisions shall apply.
A.
The use of buildings hereafter erected, enlarged, converted, structurally
altered, rebuilt or moved, and existing land shall be used only for
purposes as specified in this chapter. Furthermore, land and building
uses shall be in compliance with the regulations as established herein
for each district.
B.
All principal structures shall be located on a lot; and only one
principal structure shall be located, erected or moved onto a lot
within the R-1 and R-2 Zones, with the exception of approved planned
unit developments.
C.
Principal structures, and anything attached to them, located in an
R-1, R-2, or RR Zone shall not contain standard plain concrete or
cinder block as an exterior facade material. Exterior facades shall
be materials that are compatible with surrounding principal residential
structures. Acceptable materials include vinyl, aluminum or wood siding,
brick, sandstone, or other natural stone materials. Materials such
as corrugated metal siding/roofing, decorative split-faced block and
other materials not mentioned must be approved by the Zoning Administrator
or designee. Decisions can be appealed and approved by the Zoning
and Planning Committee.
D.
All residential roofs must have a roof style/pitch that matches the
architectural style of the structure.
[Amended 5-17-2022 by Ord. No. 2022-10]
E.
The square footage of garages that are attached to principal structures
located in an R-1, R-2, or RR Zone shall not exceed the square footage
of the first-floor footprint of the living area of the principal structure.
The roof height of the garage shall not exceed the roof height over
the living area of the principal area.
F.
Permitted uses, permitted accessory uses and conditional uses are
limited to the uses indicated for the respective zone district.
G.
Accessory buildings shall not occupy more than 30% of the rear yard. These restrictions shall apply in all districts, except as provided for in Subsection G(1) through (5) below:
[Amended 1-21-2020 by Ord. No. 2020-01]
(1)
The regulations of this Subsection G shall not apply to accessory buildings located in the AG-FP Farmland Preservation District or A-2 Agriculture District if said accessory building is used as a part of an agricultural operation located on a minimum farm site of 10 acres.
[Amended 10-18-2022 by Ord. No. 2022-31; 3-21-2023 by Ord. No. 2023-04]
(2)
Accessory buildings. In the R-1, R-2 and R-R Rural Residential Districts
and the A-2 Agricultural District not used for an agricultural operation,
the maximum size and number of residential accessory buildings permitted
on parcels shall vary depending on parcel size, as follows:
[Amended 10-18-2022 by Ord. No. 2022-31]
Parcel Size
(acres)
|
Maximum Total Square Feet Allowed per Parcel
|
Number of Accessory Buildings Permitted per Parcel1
|
---|---|---|
0.99 or less
|
900
|
1
|
1.00 to 1.49
|
1,200
|
1
|
1.50 or more
|
2.0% of the total parcel area to a maximum of 4,000 square feet
|
2
|
NOTE:
| |
1
|
In addition to a garden or tool shed not to exceed 100 square
feet.
|
(a)
Location. All residential accessory buildings shall comply with
the setbacks of the zoning district in which the property is located.
In addition:
[1]
Garden or tool sheds must be located to the rear of the front line
of the principal structure and set back a minimum of three feet from
side and rear property lines.
[2]
Residential viewshed established. Residential accessory structures shall not be located in the primary residential viewshed or secondary residential viewshed as defined in § 135-8.
[3]
Size restriction based on setback distance. Residential accessory
structures with a setback of less than 100 feet from the public right-of-way
shall not exceed 625 square feet in size. Such structures with a setback
more than 100 feet from the public right-of-way but located in front
of the leading edge of the residence shall not exceed 1,200 square
feet in size.
(b)
Materials.
[1]
The accessory building shall be constructed of materials which
are substantially similar to those used in the principal structure
with respect to texture, color and general appearance.
[2]
Garden or tool sheds are encouraged to use materials that are
similar to the principal structure, but alternative materials can
be used if approved by the Zoning Administrator.
(3)
(Reserved)
H.
Detached accessory buildings or structures shall be located no closer
than 10 feet to any other accessory or principal structure.
I.
No lot area shall be reduced so that the yards and open spaces shall
be smaller than is required by this chapter. If the lot area is less
than the minimum number of square feet required for the district in
which it is located and was of record as such at the time of the passage
of this chapter, such lot may be occupied if it meets the other district
requirements of this chapter and any other applicable state or local
regulations.
J.
The existing lawful use of a building or premises at the time of the enactment of this chapter or any amendment thereto may be continued, although such use does not conform with the provisions of this chapter for the district in which it is located, but such nonconforming use shall not be extended nor shall such building or structure be altered or enlarged, except as provided for in Subsection M.
K.
If no structural alterations are made, a nonconforming use of a building
may be changed to another nonconforming use of the same or a more
restricted classification. Whenever a nonconforming use has been changed
to a more restricted nonconforming use or a conforming use, such use
shall not thereafter be changed to a less restricted use.
L.
If a nonconforming use of a building or premises is discontinued
for a period of 12 months, any future use of the building or premises
shall conform to the regulations for the district in which it is located.
Existing farming operations shall be exempt from these restrictions.
M.
Present uses of principal or accessory buildings, signs and premises
may be continued even though they do not conform to the regulations
of this chapter. The ordinary maintenance, repair, renovation, or
remodeling of a nonconforming structure is allowed with the issuance
of an appropriate permit. However, structural repairs or alterations
of such buildings, signs or premises which require the issuance of
a permit shall not exceed 33% of the structural members of the existing
roof, walls or foundation. The expansion of a nonconforming structure
may not exceed 50% of the enclosed building area and may not increase
the nonconformity without the approval of a variance by the Board,
unless a building, sign or premises conforming to these regulations
of this chapter result. Nonconforming buildings and structures that
are damaged or destroyed by a natural event, including but not limited
to violent wind, vandalism, fire, flood, ice, snow, mold, or infestation,
may be reconstructed, provided that:
(1)
The use of the building or structure which is nonconforming as to
this chapter was not discontinued for a period of 12 months or more;
(2)
The repair and reconstruction are limited to that part of the structure
and its specific improvements which are actually damaged or destroyed
by a natural event and similar building materials shall be utilized;
(3)
The owner has the burden to establish that the damage or destruction was to a nonconforming structure or a part thereof was actually caused by a natural event and to establish the specific extent to which the damage or reconstruction occurred for the structural or part thereof that has actually been damaged or destroyed shall be reconstructed to the size, including the footprint and total square footage, location, and use, that it had immediately before the damage or destruction occurred subject to Subsection M(6);
(4)
The owner shall bear the burden as to the size, location, and use
of a damaged or destroyed nonconforming, structure or part thereof
immediately before the damage or the destruction;
(5)
The size of the nonconforming structure can be larger than the size
it was immediately before the damage or destruction is necessary to
comply with applicable local, state or federal requirement.
(6)
Repair and reconstruction shall be in compliance with all other provisions
of applicable ordinances; and
(7)
Damage was not due to an intentional act of the owner or his or her
agent.
N.
Radio and television transmitting and receiving antennas, as well
as dish antennas, shall be allowed within the lot area not required
for the building setback area in all zones and on the roof of a building
in all business and industrial zones.
O.
Satellite dish antennas larger than three feet in diameter are not
allowed on the roof of a building in any residential or agricultural
zone. However, radio and television transmitting and receiving antennas
are allowed on roofs in these zones.
P.
Site plan/development and design standards.
(1)
Introduction. This subsection is designed to provide for the future
growth and development of those multifamily residences, businesses
and industries that seek an aesthetically attractive working environment.
The intent and purpose of this subsection is to promote and maintain
desirable economic development within the Town PDD, PDD-BP, I-1 Institutional
District, B-1 Business District, B-2 Business District, LI Light Industrial
District, HI Heavy Industrial District, R-2 Residential District,
and R-3 Multiple-Family District that is practical, feasible and an
asset to owners, neighbors and the Town of Ledgeview while maintaining
an attractive environment.
[Amended 9-20-2022 by Ord. No. 2022-24]
(2)
Objectives. The purpose of this subsection is to establish rules,
regulations, standards and procedures for approval of all new development
proposals and the expansion of existing businesses and industries
and two-family and multifamily development in order to:
[Amended 9-20-2022 by Ord. No. 2022-24]
(a)
Provide for safe, efficient vehicular and pedestrian circulation.
(b)
Provide for screening, landscaping, signage, lighting and green
space.
(c)
Ensure efficient, safe and attractive land development.
(d)
Provide for compliance with appropriate design standards to
ensure adequate light and air, proper building arrangements and minimal
adverse effect on adjacent properties.
(e)
Develop proper safeguards to minimize the impact on the environment.
(f)
Ensure the provision of adequate water supply, drainage and
stormwater management, sanitary facilities and other utilities and
surveys.
(g)
Encourage modern and unique innovative design, construction,
technology and planning methods.
(h)
Advance and promote sound growth and continuous development
within the Town.
(3)
Land use/zoning. This subsection applies to the following zoning
districts: PDD, PDD-BP, I-1 Institutional District, B-1 Business District,
B-2 Business District, LI Light Industrial District, HI Heavy Industrial
District, R-2 Residential District, and R-3 Multiple-Family District.
[Amended 9-20-2022 by Ord. No. 2022-24]
(4)
Standard requirements. The interpretation and application of this
subsection shall be held as minimum requirements for the promotion
of the public health, safety and welfare.
(a)
No structure shall be erected, converted, enlarged, reconstructed
or altered, and no structure or land shall be used for any purpose
nor in any manner which is not in conformity with the provisions of
this subsection.
(b)
Where permitted and prohibited uses, site and landscape regulations,
building design criteria, off-street parking and loading requirements
and other regulations contained herein are either more or less restrictive
than comparable conditions imposed by provisions of any other law,
ordinance, rule, resolution or regulation, the requirements that are
more restrictive or which impose a higher standard shall govern.
(c)
Vision corners are required in all districts. The vision corner
will be defined as follows: beginning at the corner property line
and proceeding 35 feet along both property lines, thence connecting
these two points diagonally.
(5)
Administration. The administration of this subsection shall be vested
in the following: Town Board.
(a)
It shall be the duty of the Town Board or designated individual
to be in charge of the day-to-day administration and interpretation
of the development and design standards. Enforcement of these standards
is charged to the Ledgeview Building Inspector in accordance with
§ 62.23(7), Wis Stats.
(b)
All proposed site plans shall be forwarded to the following
Town departments: Town Clerk, Zoning Administrator, Building Inspector,
Fire Department, Public Works and Site Review/Zoning and Planning
Committee. Each department shall review each plan and make recommendations
to approve, approve with conditions or reject said plan to the Site
Review/Zoning and Planning Committee within 45 days of submittal.
These departments shall be responsive to applicants and their possible
time constraints and shall expedite the review process to the extent
possible and forward to the Town Board for final approval.
[Amended 9-20-2022 by Ord. No. 2022-24]
(c)
From time to time the design criteria may be amended, changed
or deleted. Such action shall originate before the Site Review/Zoning
and Planning Committee and be reviewed and approved by the Town Board
in accordance with § 62.23(7), Wis Stats.
(d)
Change of use or occupancy of building or structure must be
reviewed and approved by the Site Review/Zoning and Planning Committee
and Town Board.
(e)
Appeals. Unless otherwise provided herein, appeals to the requirements
contained in these standards shall be heard by the Board of Appeals.
(6)
General building and performance standards.
(a)
Purpose. The purpose of this subsection is to establish general
development performance standards in accordance with the Town of Ledgeview
Zoning Ordinance. These standards are intended and designed to assure
compatibility of uses; to prevent urban blight, deterioration and
decay; and to enhance the health, safety and general welfare of the
residents of the community.
(b)
Building. The Town of Ledgeview's overall approach encourages
a variety of architectural styles. However, basic harmony is intended
to prevail so that no one structure detracts from the attractiveness
of the overall environment. The Site Review/Zoning and Planning Committee
and the Town Board shall review building design in order to insure
architectural compatibility and integrity.
(c)
Building exterior: PDD, PDD-BP, I-1 Institutional District,
B-1 Business District, B-2 Business District, LI Light Industrial
District, HI Heavy Industrial District and R-3 Multiple-Family District.
Colors, materials, finishes and building form shall be coordinated
in a consistent manner on the front, side and rear exterior walls.
Materials shall be one of the following (color and texture to be approved):
[1]
Hard burned clay brick.
[2]
Concrete masonry. Units shall be those generally described by
the National Concrete Masonry Association as "customized architectural
concrete masonry units" or shall be broken faced brick-type units
with marble aggregate or split face or broke off concrete block. There
shall be no exposed concrete block on the exterior of any building
facing any public road. Any concrete units that have a gray cement
color shall be color coated.
[3]
Concrete may be poured in place, tilt-up or precast. Poured
in place and tilt-up walls shall have a finish of stone, a texture
or a coating. Textured finishes shall be coated. Precast units which
are not uniform in color shall be color coated. Coating shall be an
approved cementations or epoxy type with a ten-year minimum life expectancy.
[4]
Natural stone.
[5]
Glass curtain walls.
[6]
Metal siding or insulated architectural panels may be used only
in combination with one of the approved materials and with approval
of the Site Review/Zoning and Planning Committee. Metal siding may
be utilized only on the side and rear building walls that do not face
an adjacent street. Any metal siding proposed for use shall be entirely
coated with a colorfast, abrasion- and corrosion-resistant, long-life
(minimum of 20 years) finish that is resistant to chemicals, withstands
temperature extremes and has a low permeability. Any material utilized
to attach the metal siding to the building shall be concealed or the
utilization of shadow panels or semiconcealed fastener panels with
fasteners painted to match required. Color and texture to be approved.
Samples shall be provided upon request.
[Amended 9-20-2022 by Ord. No. 2022-24]
[7]
The following districts require materials listed in Subsection P(6)(c)[1] through [5] above, in minimum percentages listed below:
[Amended 9-20-2022 by Ord. No. 2022-24]
District
|
Percentage
|
---|---|
PDD-Planned Development District
|
75%
|
PDD-BP Planned Development District-Business Park
|
80%
|
I-1 Institutional District
|
75%
|
B-1 Business District
|
75%
|
B-2 Business District
|
60%
|
LI Light Industrial District
|
50%
|
HI Heavy Industrial District
|
50%
|
R-3 Multiple-Family District
|
80%
|
R-2 Residential District
|
20%
|
NOTES:
| |
1.
|
All districts listed above shall require footings and foundations
to support a structural wall above.
|
2.
|
A lock box shall be located on the exterior of the structure
in the most accessible site for Fire Department personnel, except
for development in the R-2 District.[1]
|
[8]
More or less stringent building exterior requirements than outlined
in Subsection P(16)(c)[7] may be imposed by the Zoning and Planning
Committee or the Town Board, taking into consideration public interests
such as coordinating a consistent appearance and quality of construction
with adjacent structures, alternative building materials, the use
and size of the proposed structure, the topography of the site and
the proximity of the structure to public rights-of-way and visibility
from adjacent properties.
(d)
Front building wall and building walls facing an adjacent street.
[1]
Any exterior building wall (front, side or rear) facing an adjacent street in all the districts in which design review is required shall be constructed of not less than 50% of one of the materials listed under Subsection P(6)(c)[1] through [5], unless otherwise approved by the Zoning and Planning Committee under Subsection P(6)(c)[8]. All alterations are subject to prior approval of the Site Review/Zoning and Planning Committee/Town Board.
[2]
The colors, materials and finishes shall be coordinated in a
consistent manner with other buildings within the district.
[3]
Mechanical equipment. All mechanical equipment shall be enclosed
or screened. Roof-mounted equipment shall be integrated into the design
of the structure, enclosed or screened to the extent possible.
[4]
Construction. Construction shall commence within one year of
plan approval or in accordance with a development agreement with the
Town. No site plan approval by the Site Review/Zoning and Planning
Committee shall be valid for more than 12 months from the date of
such approval unless a building permit is obtained and development
in accordance with such site plan is commenced within such period.
The provisions of this subsection shall apply unless otherwise agreed
to by the Site Review/Zoning and Planning Committee.
[5]
Maintenance. The exterior walls and roof of buildings shall be maintained in a clean, orderly and attractive condition; free of cracks, dents, punctures, breakage and other forms of visible marring. Materials that become excessively faded, chalked, cracked, chipped, damaged or otherwise deteriorated shall be replaced, refinished, repaired or repainted in accordance with the reasonable determination and order of the Building Inspector within 60 days' notice of such defect. Violations are subject to fines in accordance with Town of Ledgeview Code § 135-233A, § 778.11, Wis. Stats., or through issuance of a citation and prosecution in the Municipal Court.
[6]
No right to divide property. After a site has been purchased,
it shall not be further divided without the review and consent of
the Site Review/Zoning and Planning Committee with final approval
by the Town Board.
(8)
Lighting standards: in all districts requiring site plan review.
To provide for the basic needs of safety and security, appropriate
lighting shall be provided in order to delineate roads, drives, parking
areas, pedestrian ways, buildings and other organizational points.
Lighting shall be an integral part of the overall architectural design;
therefore, proposed lighting, whether freestanding or building-mounted,
shall complement the architectural character of the principal use.
Lighting design shall correlate energy conservation with aesthetic,
architectural and safety factors.
(a)
Any lighting used to illuminate off-street parking, loading
and service areas shall be shaded, diffused or arranged to reflect
light away from adjacent parcels and public streets. Glare, whether
direct or reflected, as differentiated from general illuminated, shall
not be visible beyond the limits of the site from which it originates.
Parking lot lights may be used in either a single or multi-format.
Characteristics, 27,000 lumen high pressure sodium/metal halide, spaced
approximately 100 feet to 120 feet off center, consisting of sharp,
cutoff-type luminaries. Maximum height for pole not to exceed 30 feet;
to be an approved metal pole. The use of wooden poles is prohibited.
(b)
Walkway lighting should be of the same family as mentioned above,
height to be 10 feet to 14 feet above grade. Bollard lighting can
be used as low-level walkway illumination on private property.
(c)
Building lighting should occur as part of the overall design
concept using recessed lighting in overhangs and at the entrance.
Well-designed soft lighting of the building exterior is allowed, provided
it does not impact on the surrounding properties, complements the
architecture and the light source is concealed.
(d)
The use of floodlights, building-mounted or otherwise, and tall
freeway-type fixtures is prohibited unless approved by the Site Review/Zoning
and Planning Committee.
(e)
Flag directional lighting is permitted with approval of Site
Review/Zoning and Planning Committee.
(9)
Site plan.
(a)
Procedure.The following procedure shall be followed for the
submittal of site plans. Where procedures and requirements imposed
by this section of this chapter are either more restrictive or less
restrictive than comparable procedures and requirements imposed by
any other provision of this chapter or any other law, ordinance, resolution,
rule or regulation of any kind, the regulations which are more restrictive
or impose higher standards or requirements shall govern.
[1]
Preliminary consultation. Prior to the submittal of a site plan,
it is recommended that the developer meet with the Town Clerk, Zoning
Administrator, Building Inspector and/or other appropriate Town staff
to discuss zoning district, site plan and landscaping plan requirements.
Such meeting should occur prior to any extensive outlay of funds on
the part of the developer since it is intended to identify potential
problems and methods to alleviate them and to encourage a cooperative
effort between the developer/owner and the Town.
[2]
Plan submittal. All site plans requiring approval by the Site
Review/Zoning and Planning Committee shall be submitted to the Town
10 working days prior to the first Monday of the month in a digital
and hardcopy format according to Town policy. All plans shall contain
the following information:
[Amended 9-20-2022 by Ord. No. 2022-24]
[a]
Name of project/development.
[b]
Location of project/development by street address
or CSM.
[c]
Name and mailing address of developer/owner.
[d]
Name and mailing address of engineer/architect.
[e]
North point indicator.
[f]
Scale.
[g]
Boundary lines of property, with dimensions.
[h]
Location identification and dimensions of existing
and proposed:
[i]
Topographic contours at a minimum interval of two
feet and key spot elevations.
[ii]
Adjacent street elevations, street rights-of-way
and proposed elevation of ground floor.
[iii]
Locations and dimensions of fire lanes.
[v]
All buildings and structures, existing and proposed,
to consider maximum development of the parcel if more than one structure
could be located on the parcel.
[vi]
Parking facilities.
[vii]
Water bodies and wetlands.
[viii]
Surface water holding ponds, drainage ditches
and drainage patterns; location and size of culverts.
[ix]
Sidewalks, walkways and driveways.
[x]
Off-street loading areas and docks.
[xi]
Fences and retaining walls.
[xii]
All exterior signs.
[xiii]
Exterior refuse collection areas must be enclosed
a minimum of three sides; open side cannot face road or must be gated
and must be located in rear of structure. R-3 Multiple-Family Districts
exterior refuse collection areas must be approved by the Site Review/Zoning
and Planning Committee.
[xiv]
Exterior lighting.
[xv]
Traffic flow on and off site.
[i]
Location of open space/green space.
[k]
Location and dimensions of proposed outdoor display
areas.
[m]
Erosion control plans.
[n]
A staging plan of any project involving more than
one phase of construction season which sets forth the chronological
order of construction and relates to the proposed uses and structures
of various service facilities and estimated completion dates.
[o]
Other information considered pertinent by Site
Review/Zoning and Planning Committee and/or the developers/owners.
[3]
Review.
[a]
Site Review/Zoning and Planning Committee. Site plans shall be forwarded to the Town Clerk 10 working days prior to the first Monday of the month. The Site Review/Zoning and Planning Committee shall review and either approve, conditionally approve or deny approval of the site plan based upon the appropriate zoning district requirements and the criteria set forth in Subsection P(9)(a)[2] above.
(10)
Landscaping.
(a)
General statement. The Town of Ledgeview finds that is in the
public interest for all developments to provide landscape improvements
for the purposes of complementing the natural environment; improving
the general appearance of the Town and enhancing its aesthetic appeal;
preserving the economic base; improving quality of life; delineating
and separating use areas; increasing the safety, efficiency and aesthetics
of use areas and open space; screening and enhancing privacy; mitigating
the diverse impact of climate; conserving energy; abating erosion
and stabilizing slopes; deadening sound; and preserving the quality
of our air and water.
(b)
Landscape plan. All applicants for building permits for PDD, PDD-BP, I-1 Institutional District, B-1 Business District, B-2 Business District, LI Light Industrial District, HI Heavy Industrial District and R-3 Multiple-Family District shall submit a landscape plan, prepared pursuant to Subsection P(10)(c) below, for review and approval as required herein prior to the request for a building permit. Where procedures and requirements imposed by this section of this chapter are either more restrictive or less restrictive than comparable procedures and requirements imposed by any other provision of this chapter or any other law, ordinance, resolution, rule or regulation of any kind, the regulations which are more restrictive or impose higher standards or requirements shall govern.
(c)
Procedure. The following procedure shall be followed for the
submittal of landscape plans:
[1]
Preliminary consultation. Prior to the submittal of a landscape
plan, it is recommended that the developer/owner meet with the Town
Clerk, Building Inspector and/or other appropriate Town staff to discuss
zoning district, site plan and landscaping plan requirements. Such
meeting should occur prior to any extensive outlay of funds on the
part of the developer since it is intended to identify potential problems
and methods to alleviate them and to encourage a cooperative effort
between the developer/owner and the Town.
[2]
Plan submittal. Landscape plans require approval by the Site
Review/Zoning and Planning Committee and shall be submitted in accordance
with Town policy for building site and operations plans. All plans
shall be contain the following information:
[Amended 9-20-2022 by Ord. No. 2022-24]
[3]
Reviews. Review of landscape plans shall be conducted concurrently
and follow the same procedure as site plan review.
(d)
Specific requirements.
[1]
Ground cover. Open space areas shall, at a minimum, be seeded
six months after completion of building. The following exceptions
may be granted by Town Staff during the review process:
[a]
The use of mulch material for shrubs and foundation
plantings;
[b]
The seeding of future expansion areas delineated
on site plan;
[c]
Areas maintained in a natural state that are undisturbed
during construction; or
[d]
Other landscape elements such as decks, patios,
stepping stones or landscape stones may be incorporated therein.
[2]
Minimum size of plantings. Required vegetation shall be of the
following minimum planting size. Plantings must be 17 feet from the
property line equally spaced one tree every 50 feet of road frontage
(minimum of two trees).
[a]
Deciduous trees: one per every 50 feet of road
frontage is required. Required size: one-and-one-half-inch diameter
as measured six inches above ground. Choice of maple, ash or a species
approved by the Site Review/Zoning and Planning Committee.
[b]
Coniferous trees: one per every 5,000 square feet
of parcel area is required. Required size: Seven feet in height at
the time of planting. Evergreen shrubs used for screening purposes,
including those used in conjunction with berms, shall be a minimum
of 24 inches in height.
[Amended 9-20-2022 by Ord. No. 2022-24]
[3]
Species.
[a]
All trees used in site development shall be indigenous
to the appropriate hardiness zone and physical characteristics of
the site.
[b]
All plant material shall conform to American Standards
for Nursery Stock, latest edition, sponsored by the American Association
of Nurserymen, Inc. All vegetation shall be planted in accordance
with accepted planting procedures.
[c]
All proposed vegetation included in the landscape
plan shall be reviewed by the Site Review/Zoning and Planning Committee
to assure compliance with the requirements contained herein.
[4]
Implementation/replacement.
[a]
All approved landscaping is to be installed in
accordance with compliance timetable.
[b]
Any vegetation included on an approved landscape
plan that dies shall be replaced by the owner/developer within one
planting season. Vegetation replaced shall conform to the approved
landscape plan and the requirements contained herein.
[5]
Maintenance. It shall be the joint responsibility of the owner
and/or lessee of the principal use, uses or building to maintain in
a neat and adequate manner all landscaping materials, vegetation,
screening and fences contained in the approved landscape and site
plans.
[6]
Compliance timetable. All landscape plans shall include a timetable
for construction, installation or planting within a period not to
exceed two years from the date of commencement of construction. Any
person who is, or has been, required to landscape any part of a zoning
lot and who has not complied with that requirement shall, within 60
days of receipt of written notice from the Zoning Administrator/Building
Inspector that a violation of this chapter exists, comply with all
requirements.
(e)
District requirements. Development within the Town shall meet
the following minimum requirements:
[2]
PDD, PDD-BP, I-1 Institutional District, B-1 Business District,
B-2 Business District, LI Light Industrial District and HI Heavy Industrial
District shall contain at a minimum:
[3]
Buffers. That portion of any business, industrial or multiple-family
district (other than duplex construction) that is abutting property
zoned for single-family residential development shall have a landscaped
area of at least six feet wide extending the full length of the business,
industrial or multiple-family district and meeting the following minimum
requirements.
[a]
One tree per 35 lineal feet, or fraction thereof,
of lot line bordering single-family districts.
[b]
A shrub, border, hedge, wall, fence, earthen berm
or other durable landscape barrier, or combination thereof, at least
four feet high, but not exceeding eight feet high, which is 90% impervious
to sight placed along the perimeter of such landscaped strip except
in the front yard setback.
[c]
When a berm or plantings, or a combination thereof,
is used as a buffer, it may exceed eight feet in height only upon
approval of the Site Review/Zoning and Planning Committee.
[d]
If a berm or buffer is erected, provisions shall
be made for stormwater runoff. A detail plan is required with submittal.
Q.
Off-street parking requirements: PDD, PDD-BP, I-1 Institutional District,
B-1 Business District, B-2 Business District, LI Light Industrial
District, HI Heavy Industrial District and R-3 Multiple-Family District.
(1)
Location. All parking spaces required to serve employees and visitors
of buildings erected or established after the effective date of this
plan shall be located on the same zoning lot as the building or use
served. Off-street parking areas may be located in the front of the
buildings in any district, with a minimum of 25 feet green space from
the property line.
(2)
Floor area. The term "floor area" for the purpose of calculating
the number of off-street parking spaces required shall be determined
on the basis of the exterior floor area dimensions of the building,
structure or use times the number of floors, minus 10%, except as
may hereinafter be provided or modified.
(3)
Nonconforming structures. Should a nonconforming structure or use
be damaged or destroyed (defined as 50% or more of the structure being
damaged) by accidental destruction, acts of God, or otherwise, it
may be reestablished if elsewhere permitted in these regulations,
except that in doing so, any off-street parking or loading space which
existed before shall be retained and expanded as necessary to comply
with the standards herein.
(4)
Change of use or occupancy of buildings. Any change of use or occupancy
of any building or buildings, including additions thereto, requiring
more parking shall not be permitted until there is furnished such
additional parking spaces as required by these regulations.
(5)
Parking dimensions and requirements. Parking dimensions and requirements shall conform to the requirements as set forth in Article XXI, Off-Street Parking Requirements.
(6)
Signs. Signing shall be regulated as set forth in Article XX, Regulation of Signs.
NOTE: At least 80% of the total required parking shall be for
full-sized vehicles and 4%, or not less than two spaces, shall be
for handicap spaces.
|
(7)
Within structures. The off-street parking requirements may be furnished
by providing spaces so designed within the principal building or structure
attached thereto; however, unless provisions are made, no building
permit shall be used to convert said parking structure into another
activity until other adequate provisions are made to comply with the
required off-street parking provisions of this chapter.
(8)
Circulation between bays. Parking areas shall be designed so that
circulation between parking bays or aisles occurs within the designated
parking lot and does not depend upon a public street. Parking area
design which requires backing into the public street is prohibited.
(9)
Driveway requirements. Notwithstanding other provisions of this chapter
concerning appeals and review of plans submitted hereunder, permits
for and review of driveway approaches shall be as provided:
(a)
All off-street parking spaces shall have access from driveways
and not directly from the public street.
(b)
Driveway access curb opening on a public street shall not be
located less then 12 feet from each other, and maximum 40 feet in
width.
(c)
The number and locations of curb cuts shall be as determined
by the Building Inspector upon consultation with the Site Review/Zoning
and Planning Committee, taking into consideration traffic flow, safety
concerns and the needs of the business.
(d)
Joint driveways are encouraged and require appropriate Town
staff approval, maximum 50 feet in width.
(10)
Drainage. All sites must have stormwater management plans, including
adequate parking and drainage.
(11)
Surfacing.
(a)
PDD, PDD-BP, I-1 Institutional District, B-1 Business District,
B-2 Business District, and R-3 Multiple-Family District.. All areas
intended to be utilized for parking space and driveways shall be surfaced
with bituminous asphalt or concrete and are to be installed within
one year of completion of construction. Plans for surfacing and drainage
of driveways and parking areas for five or more vehicles shall be
submitted.
[Amended 9-20-2022 by Ord. No. 2022-24]
(b)
LI Light Industrial District and HI Heavy Industrial District
industrial districts. In areas intended to be utilized for parking
space and driveways, up to 20 feet beyond the rear of the buildings
are to be surfaced with bituminous asphalt or concrete. Non-hard-surfaced
areas are to be approved by the Site Review/Zoning and Planning Committee.
(c)
Fire lanes. In all districts, fire lanes must be 25 feet in
width and shall be surfaced with bituminous asphalt or concrete.
(12)
Striping. All parking stalls shall be marked with painted lines
not less than four inches wide.
(13)
Lighting. Any lighting used to illuminate an off-street parking
area shall be so arranged as to reflect the light away from adjoining
property and directed downward, abutting residential uses and public
rights-of-way.
(14)
Signs. No sign shall be so located as to restrict the sight
lines and orderly operation and traffic movement within any parking
lot.
(15)
Curbing. All off-street parking shall have a perimeter concrete
curb and gutter around the entire parking lot unless the site plan
shows that runoff from the parking lots will not cause erosion or
adversely affect adjacent properties.
(16)
Parking lot landscaping. To avoid the undesirable monotony,
heat and wind associated with large parking lots, such lots shall
have a minimum of one internal landscaped island delineator in addition
to any required traffic safety island for each 21,780 square feet
(1/2 acre) or fraction thereof of off-street parking space; such islands
shall be a minimum of 360 square feet (two parking spaces) and shall
be bounded by concrete curbing. Trees may be installed in approved
traffic safety islands used to delineate parking spaces from driving
aisles and in other areas. The internal landscaped island(s) required
above may be deleted if the aggregate area and trees of individual
traffic islands meets or exceeds the above requirement.
(17)
Parking lot screening. The parking or storage of licensed motor
vehicles, if not within an enclosed building structure, shall be effectively
screened as defined.
(18)
Planting standards. All plant material shall conform to the
specifications and procedures stated in the landscape plan requirements
section of these standards. Landscaping, except required grass or
ground cover, shall not be located closer than six feet from the edge
of any driveway pavement or within the established right-of-way and
must maintain a ten-foot clearance at curbside.
(19)
Maintenance. It shall be the joint and severable responsibility
of the lessee and owner of the principal use, uses or building to
maintain in a neat and adequate manner the parking space, accessways,
striping, landscaping, screening and required fences.
(20)
Use of required area. Required accessory off-street parking
spaces in any district shall not be utilized for open storage, sale
or rental of goods or storage of inoperable vehicles without approval
of the Site Review/Zoning and Planning Commission.
R.
Off-street loading requirements: PDD, PDD-BP, I-1 Institutional District,
B-1 Business District, B-2 Business District, LI Light Industrial
District and HI Heavy Industrial District.
(1)
Minimum facilities. All warehousing, manufacturing plants or any
other building where large amounts of goods are received or shipped
shall provide adequate loading and unloading berths as determined
by the Site Review/Zoning and Planning Committee.
(2)
Location.
(a)
All required loading berths shall be off-street and located
on the same lot as the building or use to be served.
(b)
Loading berths shall not occupy the front yard.
(c)
Loading berths located at the side of buildings on a corner
lot shall observe the following requirements.
(d)
Each loading berth shall be located with appropriate means of
vehicular access to a street in a manner which will cause the least
interference with traffic.
(3)
Size. A required off-street loading berth shall be at least 55 feet
in length, exclusive of aisle and maneuvering space, and shall have
a vertical clearance of at least 15 feet.
(4)
Surfacing. All areas intended to be utilized for off-street loading
shall be surfaced with bituminous asphalt or concrete. Any non-hard-surfaced
areas are to be reviewed and approved by the Site Review/Zoning and
Planning Committee.
(5)
Utilization. Space allocated to any off-street loading shall not,
while so allocated, be used to satisfy the space requirements for
any off-street parking facilities.
(6)
Change of use. Where a change of use in off-street loading facilities
is made necessary due to damage, destruction, increased use or any
other change of use, such change shall be approved by the Site Review/Zoning
and Planning Committee.
S.
Outdoor storage. Outdoor storage of any material other than licensed
motor vehicles is prohibited. Storage of materials, equipment, parts,
inventory, etc., shall take place in enclosed structures that meet
the general building and performance requirements contained herein.
Upon approval by the Site Review/Zoning and Planning Committee, a
90% impervious fence may be used under certain circumstances. Outdoor
storage of licensed motor vehicles condition is allowed, provided
such outdoor parking (storage) areas are screened pursuant to the
definition of screening contained in the definitions section.
T.
Utilities. Any new development requiring Town approval under this chapter, including but not limited to rezoning or conditional use permit approval and which includes installation of any new utility service to the property on which the new development is located, shall install all utilities underground. Exceptions may be granted by variance under § 135-248.
U.
Animal unit calculations.
(1)
General provisions.
(a)
No livestock will be allowed on lots or parcels of less than 1.99 acres in the Town of Ledgeview, except chickens as outlined in Subsection V.
(b)
These provisions shall apply to all parcels of land zoned RR and AG2 in the Town of Ledgeview. The keeping of livestock within other zoning districts except AG-FP or A-2 is hereby prohibited. Parcels of land zoned AG-FP are exempt from this subsection and shall be regulated as outlined in Article X: AG-FP Farmland Preservation District.
(c)
Parcels or lots within districts zoned RR or AG2 having a larger
number of livestock at the time of adoption of this subsection may
continue to maintain that number of animal units, provided that no
expansion of the facility shall be permitted without an approved conditional
use permit from the Town of Ledgeview.
(2)
Calculation.
(a)
To determine the number of permitted animal units per lot or
parcel, property owners shall multiply the total number of acres owned
less 1.99 acres times the appropriate livestock multiplier[2] to determine the total number of allowable animal units.
(b)
For young livestock after one year of age, livestock must be
in strict compliance with the equivalency calculations.
(c)
All lands under identical ownership which are contiguous, as
defined in the Town of Ledgeview Code of Ordinances, may be included
in the total acreage calculation for the purposes of this section.
(d)
The total number of livestock permitted is cumulative regardless
of the species of the livestock.
(3)
Examples.
(a)
Owner of residence located on four acres would like horses:
4.00
|
acres
|
- 1.99
|
acres
|
= 2.01
|
acres
|
2.01
|
acres
|
x 1.000
|
horse multiplier
|
= 2 horses
|
(b)
Residence located on four acres would like alpacas:
4.00
|
acres
|
- 1.99
|
acres
|
= 2.01
|
acres
|
2.01
|
acres
|
x 10.00
|
alpaca multiplier
|
= 20 alpacas
|
(c)
Residence located on four acres would like both horses and alpacas:
4.00
|
acres
|
- 1.99
|
acres
|
= 2.01
|
acres
|
1
|
acre for horse (1 acre x 1.000 horse multiplier = 1 horse)
|
1.01
|
acres remaining for alpacas (1.01 acres x 10.000 sheep multiplier
= 10 alpacas)
|
(4)
For the purposes of this calculation, less than 0.50 livestock shall
be rounded down to the next nearest whole number and 0.50 or greater
shall be rounded up the next whole number.
(5)
A conditional use permit shall be required for any excess livestock
as calculated herein.
(6)
Livestock multiplier table.
Type of Livestock
|
Multiplier
|
Equivalency
(units)
|
---|---|---|
Dairy Cattle
| ||
Milking and dry cows
|
0.714
|
1.400
|
Heifers (800 to 1,200 pounds)
|
0.909
|
1.100
|
Heifers (400 to 800 pounds)
|
1.667
|
0.600
|
Calves (under 400 pounds)
|
5.000
|
0.200
|
Beef Cattle
| ||
Steers or cows (600 pounds to market)
|
1.000
|
1.000
|
Calves (under 600 pounds)
|
2.000
|
0.500
|
Bulls
|
0.714
|
1.400
|
Swine
| ||
Pigs (55 pounds to market)
|
2.500
|
0.400
|
Pigs (up to 55 pounds)
|
10.000
|
0.100
|
Sows
|
2.500
|
0.400
|
Boars
|
2.000
|
0.500
|
Sheep (llama, alpaca, goat)
| ||
Per animal
|
10.000
|
0.100
|
Horses
| ||
Per animal
|
1.000
|
1.000
|
Ducks
| ||
Per bird (wet lot)
|
5.000
|
0.200
|
Per bird (dry lot)
|
100.000
|
0.010
|
Chickens
| ||
Layers
|
100.000
|
0.010
|
Broilers
|
200.000
|
0.005
|
Broilers (continuous overflow watering)
|
100.000
|
0.010
|
Layers or broilers (liquid manure system)
|
30.000
|
0.033
|
Turkeys
| ||
Per bird
|
56.000
|
0.018
|
V.
Keeping of chickens on residential property.
(1)
Applicability. Properties less than 1.99 acres in total land area
shall be permitted to keep chickens on their property in accordance
with this subsection and the following:
(a)
The property is zoned R-1 Residential District or R-R Rural
Residential District.
(b)
The property upon which the fowl are kept shall have established
a principal single-family use conforming to the zoning district.
(c)
The word "keep" shall mean either the owning, keeping, possessing
or harboring of a chicken.
(2)
Permit required.
(a)
Any person who keeps chickens on land in the Town which the
person owns, occupies, or controls shall obtain a permit issued by
the Clerk-Administrator. The permit is valid for a calendar year (January
1 through December 31). Only one permit per zoned parcel is allowed.
(b)
Permit applications submitted by a person other than a record
title owner of the property upon which chickens will be kept shall
provide written consent of the property owner with the permit application.
(c)
All permit applications shall be accompanied by satisfactory
evidence that the applicant has registered the proposed location with
the Wisconsin Department of Agricultural Trade and Consumer Protection
(DATCP) pursuant to § 95.51, Wis. Stats., and Ch. ATCP 47,[3] Wis. Adm. Code.
[3]
Editor's Note: See Ch. ATCP 51, Wis. Adm. Code.
(d)
The Town shall provide written notification to all adjacent
property owners of the permit to keep chickens.
(3)
Number. The keeping of up to four hens (female Gallus gallus domesticus)
is allowed. The keeping of roosters of all types and guinea hens is
prohibited.
(4)
Coop. A covered coop or shelter shall be provided for the keeping of all chickens. Coops may be mobile to be relocated on the property. The coop shall comply with the regulations outlined in § 7-5, Keeping of fowl, and the location requirement outlined in Subsection V(6) below. A building permit for the coop shall be required.
(5)
Enclosure or chicken run. Chickens shall not be allowed to free range.
All chickens shall be contained within a fenced enclosure area or
chicken run that is contiguous with the coop.
(6)
Location. The required covered coop and the fenced enclosure area
shall comply with the setback requirements for a principal structure
as prescribed for the zoning district in which it is located. No coop
shall be located between the principal structure and the public right-of-way.
(7)
Public health requirements.
(a)
Chickens shall be kept and handled in a sanitary manner to prevent
the spread of communicable diseases among birds or to humans.
(b)
Any person keeping chickens shall immediately report any unusual
illness or death of chickens to the Health Department.
(c)
The Health Officer may order testing, quarantine, isolation,
vaccination or humane euthanasia of ill chickens or chickens believed
to be a carrier of a communicable disease. The owner of the chicken
shall be responsible for all costs associated with the procedures
ordered hereunder.
(8)
Slaughtering. No chickens may be slaughtered on properties zoned
or within the boundaries of the Town unless such slaughtering activity
occurs on property zoned agricultural.
(9)
Sale of eggs and baby chicks. No person may offer to sell eggs or
chicks accumulated from the activities permitted by this subsection.
(10)
Fee. The Town Board may by ordinance or resolution establish
reasonable fees for the administration costs associated with monitoring
and enforcing these regulations or for licensing for the keeping of
hens.
(11)
Violations. Violations of the requirements in this subsection
may result in nuisance enforcement by the Town Zoning Inspector. Revocation
of the permit may occur if there are three or more violations within
a calendar year period. Enforcement related to the keeping of chickens
using the following process:
(a)
The Town received and records a written complaint.
(b)
The Code Enforcement Officer investigates the complaint.
(c)
If there is determined to be a violation, the Zoning Inspector
contacts the permit owner of the violation, outlines his or her responsibility
to correct the violations, and specifies the date to complete the
corrections. If the Zoning Inspector cannot contact the owner, the
Zoning Inspector will send the permit owner a written "notice of violation"
with information regarding the violation, his or her responsibility
to correct the violations, and a date to complete.
(d)
The Zoning Inspector revisits the site to check on compliance.
(e)
If the violation is not corrected or it is the third recorded
violation in a calendar year, the Zoning Inspector forwards the violation
to the Town Board for revocation of the permit.
W.
Home occupation.
(1)
Regulations for home occupation:
(a)
The use shall be conducted entirely within a dwelling and carried
on by the inhabitants hereof and no others.
(b)
The use shall be clearly incidental and secondary to the use
of the residence for dwelling purposes, and the appearance of the
structure shall not be altered or the occupation within the residence
be conducted in a manner that would cause the premises to differ from
its residential character either by the use of colors, materials,
construction, lighting, signs or the emission of sounds or vibrations
that carry beyond the premises.
[1]
There shall be no display of products visible in any manner
from the outside of the dwelling.
[2]
No advertising display signs shall be permitted.
[3]
No equipment or process shall be used in a home occupation which
creates noise, vibration, glare, fumes or odor detectable to the normal
senses off the property.
(c)
No storage of goods, materials or products connected with a
home occupation shall be allowed in accessory buildings, detached
garages or outside of the dwelling.
(d)
The area set aside for home occupations shall not exceed 20%
of the total floor area of such residence.
(e)
A home occupation shall not create greater vehicle or pedestrian
traffic than normal for the district in which it is located, and there
shall be no deliveries to or from a home occupation with a vehicle
larger than a 26,000-pound GVW truck.
(f)
The use shall not require additional off-street parking spaces
for clients or customers of the home occupation.
(g)
No home occupation shall cause an increase in the use of any
one or more public utilities (water, sewer, electricity and garbage
collection) so that the combined total use for dwelling and home occupation
purposes exceeds the average for residences in the neighborhood.
(h)
Direct sales of products on display shelves or racks are not
allowed, but a person may pick up an order placed earlier, although
delivery of that item to the buyer should occur off the premises whenever
possible.
(i)
No motor power other than electrically operated motors shall
be used in connection with a home occupation.
(2)
Sale of personal property. Notwithstanding any provision contained
herein to the contrary, garage, basement, yard, consignment, or other
similar sales shall not be allowed more than four times each year,
one per quarter, and each sale shall not last more than 72 consecutive
hours.
X.
Automobile
fueling stations, service stations, and convenience stores (including
automotive repair facilities and fueling stations with automotive
repair facilities).
[Added 5-4-2020 by Ord. No. 2020-04]
(1)
Purpose.
The purpose of this subsection is to regulate the development of fueling
stations, service stations, and convenience stores to ensure that
the design and operation of such uses effectively mitigate associated
problems with traffic, congestion, excessive pavement and lighting,
litter, hazardous materials, and noise.
(3)
Location
and separation requirements. Fueling stations shall be separated by
a minimum of 500 feet, except that a maximum of two fueling stations
are permitted at any single intersection. Separation distance shall
be measured in a straight line from the property line of said fueling
stations. Where two fueling stations are located at a single intersection,
the Town encourages fueling stations to be sited in such a manner
as to serve different flows of traffic. The Town may waive the spacing
requirements for infill sites or locations affected by roadway widening
or other infrastructure improvements.
(4)
Development
and operational standards.
(a)
The development standards in this section are intended to supplement
the standards in the underlying zoning district for fueling station
uses. In the event of conflict between these standards and the underlying
zoning district standards, the provisions of this section shall apply.
Fueling station uses shall also comply with all applicable state and
federal regulations regarding site design, pricing signs, containment,
maintenance, and operations.
(b)
Lot coverage.
[1]
Buildings. Maximum lot coverage fo ra service station or convince
store (including attached or detached car wash) is 20% of the total
lot area.
[2]
Canopy. No more than 15% of the total lot area shall be covered by
a canopy.
[3]
Greenspace or permeable surface. Twenty-five percent of the total
lot area shall remain green space.
(5)
Vehicle
access/circulation. The intent of the specific access and circulation
standards below is to ensure safe and convenient internal circulation
and access to and from the site, while minimizing the negative visual
impact of multiple curb cuts, discontinuous landscape, and excessive
pavement.
(a)
All fueling station developments shall have direct access to an arterial
street which is a federal, state, or county designated highway, except
where it is part of a nonresidential development where access is provided
by a parallel access road or reverse frontage road where nonresidential
uses will be on both sides of the street.
(b)
No more than two exterior points of access (driveways along abutting
streets) shall be provided for each fueling station, regardless of
the length of street frontage. Accesses, or curb cuts, shall not exceed
35 feet in width. Within integrated developments, shared access driveways
are preferred.
(c)
The internal circulation system shall allow for vehicle stacking
without blocking site ingress or egress. The pump island shall be
situated to provide stacking space for a minimum of two vehicles behind
the vehicle parked at the pump closest to the entrance and/or exit
driveway. The Town may consider deviations from this requirement through
the design review process.
(6)
Pedestrian
access to building. A minimum of one continuous four-foot-wide internal
pedestrian walkway shall be provided from the perimeter public sidewalk
of each abutting street to the nearest entrance to the building. Internal
pedestrian walkways shall be distinguished from driving surfaces through
the use of sidewalks, special pavers, bricks, scored/stamped concrete,
or high-visibility pavement parking.
(7)
Building
orientation. Buildings shall be placed close to the street and oriented
to the public view.
(8)
Building
design. The building shall be designed for architectural compatibility
with the surrounding area. The buildings shall use the same architectural
materials on all sides of the building. All such buildings shall be
constructed of brick masonry, split face concrete block, or stone.
Additionally, all convenience stores abutting residential uses and
zoning districts shall have pitched roofs matching the roof lines
of adjoining residential structures.
(9)
Pump
islands and canopy design.
(a)
Canopies over public islands.
[1]
Obstruction of visibility at rights-of-way prohibited. The canopy
shall not block visibility at intersections of rights-of-way or drives.
[2]
Canopy fascia shall match the color and texture of the primary building.
Canopy roofs shall be architecturally consistent with the main building.
Canopy clearance:
[a]
Covering islands with a combination of unleaded, diesel, kerosene,
or compressed natural gas fuel pumps. The maximum height of the canopy
clearance shall be 15 feet and the maximum width of the canopy fascia
shall be 30 inches.
[b]
Covering islands with dedicated (only) diesel fuel or compressed
natural gas fuel pumps. The maximum height of the canopy clearance
shall be 18 feet and the maximum width of the canopy fascia shall
be 30 inches.
[3]
The columns of the canopy structure shall be clad with brick, block,
or stone to match the building, and the cladding shall extend to a
minimum height of 12 feet as measured from grade.
(b)
Pump islands.
[1]
Shall be located a minimum of 20 feet from any property line to the
nearest edge of the pump island; however, a canopy or roof structure
over a pump island may be constructed to within five feet of a street
side property line.
[2]
A minimum of 25 feet separation from pump island to pump island or
pump island to any structure.
[3]
A minimum of 30 feet from the pump island to the end of the parking
stalls.
(10)
Signs. All signs, except window signs, shall be constructed and maintained within a permanent sign structure. Except as provided below, signs are subject to compliance with the provisions of Chapter 79, Signs.
(a)
Canopy signs. Signs or distinctive emblems may be considered for
the canopy. Canopy signage shall be permitted on no more than two
sides of the canopy fascia. Signage must be location on the fascia
facing a public roadway.
(b)
Motor fuel pricing signs. Signage for advertising the price of fuel shall be integrated into the freestanding sign. Motor fuel pricing signage may be electronic in nature, and shall not count against the maximum size electronic message sign as permitted in Chapter 79, Signs.
(c)
Prohibited signs. The following signs are hereby prohibited:
[1]
Any sign that would directly face a residential structure.
[2]
Any sign which, or any part of which, is in motion by any means,
including fluttering or rotating, or other signs set in motion by
movement of the atmosphere. This includes decorative flags, pennants,
whirling objects, banners, or other entity(ies) attached to strings
or lines.
[3]
Inflatable advertising devices or signs.
[4]
Changeable copy and portable trailer signs, either fixed or moveable
except gas prices consistent with state and/or federal regulations
and practice of the industry.
[5]
Banners or placards which are temporary signs or devices of paper, fabric, plastic, or other flexible materials and are suspended by wires or poles to advertise a special event (except as may be permitted for temporary signs by Chapter 79, Signs).
[6]
A sign on a motor vehicle or trailer parked on public or private
property so as to be seen from the public right-of-way for more than
three consecutive hours, which has attached thereto or located thereon
any sign for the purpose of advertising a product or directing people
to a business activity.
[7]
Exposed neon or similarly appearing signage.
(11)
Parking. In addition to the off-street vehicle parking provisions in Chapter 135, Article XXI, the following standards apply to fueling station uses:
(a)
Customer and employee parking shall not be utilized for vehicle repair,
finishing work or storage of vehicles. No vehicle which is waiting
for service, or which has been serviced, shall be parked on site for
a period of longer than 72 hours.
(b)
No vehicle shall be parked on the premises for the purpose of offering
it for sale.
(12)
Lighting. In addition to the lighting provisions of § 135-18.1, the recommendations outlined in the "Lighting Handbook, 10th Edition" developed and published by the Illuminating Engineering Society (IES) shall apply.
(a)
Site. Pole heights including the bases shall not exceed 15 feet in
height. Lighting bases shall not be exposed more than one foot above
grade. Proposed fixtures must be Dark Sky compliant, and cut-sheets
must be provided to confirm. Lighting levels on the site shall not
exceed 15 footcandles, and the maximum lighting level permitted at
the property line is 0.5 footcandle.
(b)
Building. Lighting levels around the foundation of the building and
under the soffits shall not exceed 10 footcandles.
(c)
Canopy. Canopy lighting shall be recessed so that the luminaire does
not extend below the surface of the underside of the canopy. Lighting
levels for fuel pumps under the canopy shall not exceed 20 footcandles.
(13)
Landscaping. To provide adequate screening for the large expanses
of pavement associated with fueling station use, a minimum of 15%
of the site shall be landscaped, concentrated at the perimeter of
the site.
(a)
Street frontage landscaping shall be a minimum of 10 feet in width
with intermittent berms to mitigate sight lines. Side property line
landscaping shall be a minimum of five feet in width. Parking lot
islands shall be landscaped. Islands shall be landscaped with trees,
shrubs, and/or ground cover.
(b)
Planter areas adjacent to the building shall be provided.
(14)
Protective bollards or similar. The use of bollards to protect buildings,
pump islands, canopies, or other improvements on the site shall be
at the sole discretion of the Zoning and Planning Commission and the
Town Board as part of the conditional use permit approval. The use
of large or permanent planters in front of the building primary entrance
shall be strongly encouraged.
(15)
Outdoor display of materials or merchandise. The outdoor storage
or display of merchandise shall be permitted only within five feet
of the foundation of the principal building on the site. Outdoor storage
and display of merchandise shall include, but not be limited to, ice
storage or vending boxes, vending machines, and/or propane tanks and
or other flammable materials.
(16)
Concrete curb and gutter required. Concrete curb and gutter shall
be required throughout all off-street parking, drive, and loading
areas of the development.
(17)
Noise.
(a)
Outdoor speakers. All outdoor speakers and video/audio pump stations
and sound signals associated with the service stations shall be turned
off daily between the hours of 10:00 p.m. and 7:00 a.m.
(b)
Car wash air dryers. For car wash facilities that use forced air
dryers, the maximum permitted sound level shall not exceed 67 decibels
as measured at any point of the boundary or property line of the site
on which the facility is located.
(18)
Hours of operation. Hours of operation shall be established by the
Town Board following recommendation by the Zoning and Planning Commission.
(19)
Accessory uses (such as food establishments or financial institutions).
Food establishment and financial institution uses may be permitted
as an accessory use if such uses do not occupy more than 25% of the
floor area of the principal structure and is housed completely within
the principal structure. The Town may impose hours of operation for
the accessory uses different from the hours of operation of the principal
use.
(20)
Other requirements. Any other requirements and/or conditions deemed
appropriate by the Zoning and Planning Commission and/or Town Board
to ensure the health, safety, and welfare of the community.
A.
Except as otherwise provided in this chapter, the height of any building
hereafter erected, converted, enlarged or structurally altered shall
be in compliance with the regulations established herein for the district
in which such building is located.
B.
Accessory farm buildings, belfries, chimneys, cooling towers, elevator
bulkheads, fire towers, monuments, silos, scenery lofts, tanks, water
towers, ornamental towers, spires, wireless television or broadcasting
towers, masts or aerials, telephone, telegraph and power transmission
poles and lines, microwave radio relay structures and necessary mechanical
appurtenances are hereby exempted from the height regulations of this
chapter.
C.
Churches, schools and other public and quasi-public buildings may
be erected to a height not exceeding 60 feet nor five stories, provided
that the front, side and rear yards required in the district in which
such a building or structure is to be located are each increased at
least one foot for each foot of additional height above the height
limit otherwise established for the district in which such building
or structure is to be located.
A.
No front yard shall be used for open storage of boats, vehicles or
any other equipment.
B.
Where a residential lot has an area less than the minimum number
of square feet per family as required for the district in which it
is located and was of record as such at the time of the passage of
this chapter, such lot may be occupied by one family, subject to the
setback, rear yard and side yard regulations for the district in which
it is located.
C.
No part of a yard or other open space provided about any building
for the purpose of complying with the provisions of this chapter shall
be included as part of a yard or any other open space required for
another building.
D.
Attached garages, decks or other structures which are part of the
main building or are substantially attached thereto shall meet the
side yard and rear yard setback requirements within each zoning district
for the principal structure.
E.
Every part of a required setback shall be open to the sky unobstructed,
except for the ordinary projections including, but not limited to,
sills, overhangs, cornices and ornamental features projecting not
more than two feet. Setbacks are established from the property line
to the closest foundation or structural surface including, but not
limited to, decks, fireplaces, windows or steps. If a larger overhang
is required, the setback area must be recalculated to accommodate
the additional width of the overhang.
A.
Purpose. The purpose of this section is to regulate the materials,
location, height and maintenance of fencing, landscaping walls, visual
screening and decorative posts, herein referred to as "fence," and
to impose fencing requirements in order to protect the public health,
safety and welfare by preventing the creation of nuisances and safety
hazards and to protect property values and aesthetics in the Town
of Ledgeview.
B.
Applicability. The permit requirements of this section apply to all
fences, which shall include any physical barrier enclosing or partially
enclosing any property or portion thereof constructed of wood, stone,
plastic, brick, metal, or other similar materials or any combination
thereof. This section does not apply to underground pet containment
systems.
C.
Permit required. No person shall construct, erect, extend, modify
or otherwise install any fence within the Town of Ledgeview without
first obtaining a fence permit from the Zoning Administrator. No permit
shall be required for minor maintenance activities such as painting
or repair work unless any elements anchoring the fence to the ground
are being moved, removed or replaced or there is a change in materials,
construction or appearance of the fence.
[Amended 5-17-2022 by Ord. No. 2022-10]
D.
Permit application.
(1)
Applications for a permit shall contain the following information:
(a)
A site plan of the property depicting the current improvements,
any public or private right-of-way or easements, utilities, including
but not limited to fire hydrants, stormwater or drainage management
facilities and easements and the proposed fence locations with dimensions
from property boundaries. A survey may be required if the existing
survey, property markers or natural monuments do not sufficiently
identify property boundaries for the Zoning Administrator.
[Amended 5-17-2022 by Ord. No. 2022-10]
(b)
A pictorial representation of a typical fence section and any
substantially dissimilar sections or access points.
(c)
The maximum height above original grade and length of the proposed
fence.
(d)
Any additional information requested by the Zoning Administrator
reasonably necessary to further the purposes of this section.
[Amended 5-17-2022 by Ord. No. 2022-10]
(e)
If encroaching on adjoining property, any agreement(s) from
the property owner(s) requested by the Zoning Administrator.
[Amended 5-17-2022 by Ord. No. 2022-10]
E.
General requirements.
(1)
Materials.
(a)
Walls and fences shall be constructed of high-quality materials
and of good appearance, such as decorative blocks, brick, stone, treated
wood, redwood, cedar, vinyl, wrought iron or similar materials.
(b)
Galvanized steel chain-link fencing or vinyl-coated chain-link
fencing may be used. This type of fencing shall not be used in the
front yard or past the front setback of the home.
(c)
Agricultural mesh fencing and poles may be used for the protection
of gardens, trees, shrubs and other plants that may be endangered
by animals.
(d)
No person shall use rope, string, wire products, including but
not limited to chicken wire, hog wire, wire fabric, barbed wire (except
as allowed in other sections of this Code), razor ribbon wire, field
wire, barbless wire, agricultural mesh, and similar welded or woven
wire fabrics, chain, netting, cut or broken glass, paper, metal panels,
plywood, fiberglass panels or plastic panels in any fence or any other
materials that are not manufactured specifically as fencing materials.
The Zoning Administrator may require the applicant to provide the
manufacturer's standards to establish the intended use of a proposed
fencing material.
[Amended 5-17-2022 by Ord. No. 2022-10]
(e)
No person shall construct a fence of wood, metal or plastic
products that are designed specifically for uses other than fence
construction.
(f)
No person shall construct a fence of used, damaged or unsafe
materials.
(g)
No person in residential zones shall weave or use slats of any
material, including but not limited to metal, fiberglass, or bamboo,
through a chain-link fence to create a blind fence, screening fence
or any other type of fence addressed in this chapter.
(h)
Used materials, equipment and devices shall not be reused unless
it can be determined by the Zoning Administrator that they meet the
requirements of the Building Code for new materials.
[Amended 5-17-2022 by Ord. No. 2022-10]
(i)
No person shall place, erect, install, build, construct, add
as a repair item, use and/or maintain any fence or barrier consisting
of, or made of what is commonly known as, railroad ties, blocking
lumber, pallets, or similar materials.
(j)
No agricultural-style metal fence posts shall be exposed to
view, except in an agricultural district; no snow fence materials
shall be used for permanent fencing and no single or double strands
of wire shall be used for a temporary or permanent fence.
(2)
Rapid entry/Knox-Box®. A Knox-Box® may be required by the Building Inspector and/or Fire Department at access points as outlined in Chapter 49.
(3)
Location.
(a)
All fences shall be located completely upon the owner's property.
Encroachment on any easement will require approval from the easement
beneficiary. Fences proposed on an adjoining property may be permitted
with written approval from the adjoining property owner. Fences located
in easements may require an agreement to be signed and filed with
the Brown County Register of Deeds Office.
[Amended 9-20-2022 by Ord. No. 2022-25]
(b)
No fence located in a front yard or yard abutting any street
shall be located closer than two feet from the property line.
(c)
Fences shall not be constructed in any way that could impair
ingress or egress from any building, including emergency egress from
window openings.
(d)
Fences may be located on the property line on any side or rear
yard not abutting a street, provided that all maintenance, including
staining or painting, can be performed without trespassing on adjoining
property either as a function of fence design or through a maintenance
easement agreement with the neighboring property owner, which shall
be recorded with the County Register of Deeds.
(e)
[1]Fences shall not be erected in a location or manner that
could constitute a traffic hazard, including, but not limited to,
the area established by drawing a line across the corner of the property
at a public road intersection from the two points along the adjacent
public road right-of-way boundaries 25 feet from the corner of said
boundaries.
[1]
Editor's Note: Former Subsection E(3)(e), which provided that
fences shall not be erected within drainage easements without written
approval from the Utility Department, was repealed 9-20-2022 by Ord. No. 2022-25, which ordinance also redesignated former Subsection E(3)(f)
as Subsection E(3)(e).
(4)
Height.
[Amended 9-20-2022 by Ord. No. 2022-25]
(a)
The fence height shall be measured from the grade surface directly
vertical to the top of the fence at any location along the fencing.
If a fence is placed atop an earthen berm, the height of the fence
shall be measured from the original grade or the berm as determined
by § 135-15.1(A)(5).
(b)
Privacy fences erected in front yards shall not exceed three
feet in height.
(c)
Privacy fences erected in side yards adjacent to any public
street shall not exceed four feet in height unless the fence is located
no closer than the leading edge of the principal structure.
(5)
Construction and maintenance.
(a)
All fences shall be erected and maintained such that materials
are in sufficiently good condition to maintain the structural integrity
and visual appearance of the fence. Painted or stained surfaces shall
be retouched or refinished to prevent an uneven or worn appearance.
(b)
Structural and support components shall face away from adjacent
properties.
F.
Required fencing.
(3)
Mechanical equipment screening. Except for residential and agricultural
uses, all outdoor mechanical equipment, whether ground-mounted or
roof-mounted, including, but not limited to, air-conditioning and
ventilation equipment, shall be screened from public view. Screening
shall be of sufficient height and opacity to screen such equipment
from public view. Materials shall be consistent with or complementary
to the surrounding facade and overall building appearance.
(4)
Salvage yards. Salvage yards shall be completely enclosed by a solid
opaque wall or fence and solid access gates at a height not greater
than eight feet.
(5)
Outdoor storage, dumpster and garbage screening.
(a)
All premises or areas, except residential and agricultural uses
within the R-1, R-2, RR, A-1 and A-2 Districts, used for outdoor storage
of materials, including, but not limited to, bulk storage, inoperable
vehicles, automobile parts, scrap metal, lumber, and building materials
and any garbage cans, dumpsters or other permitted outdoor refuse
collection and storage shall be completely enclosed by a fence not
less than six feet nor more than eight feet in height to screen such
areas from ordinary public view. Such fence shall be 90% opaque.
(b)
No materials or refuse stored may protrude above the top of
the fence.
(c)
All screening required under this subsection, except those located
in the Heavy Industrial District, shall be required to be constructed
of materials of a similar or complementary texture, color and style
as any principal structure located on the premises.
(d)
Visual screening for outdoor storage, not including incidental
garbage collection storage, may be accomplished through the use of
earth berms, plantings or combination thereof. Fencing may be required,
however, if the nature of the storage suggests fencing is necessary
for public safety.
(6)
Outdoor alcohol-licensed premises.
[Amended 3-7-2022 by Ord.
No. 2022-02]
(a)
All outdoor areas included in the liquor license for a premises under Chapter 5 of the Town of Ledgeview Code shall be enclosed by a fence or other measures intended to provide control over the operations of the beer garden. All required fencing shall be constructed a minimum of five feet from the property line, with a minimum height of four feet and a maximum height of six feet.
(b)
Areas subject to temporary/special event alcohol licenses shall install
temporary fencing 48 inches or greater to surround the entire outdoor
licensed area. All openings for ingress and egress shall be monitored
to ensure underage persons are not permitted to enter except as authorized
by § 125.07, Wis. Stats.
G.
Security fences.
(1)
All fences erected as security fences require the approval of the
Town Board. The Town Board may disapprove a permit for security fencing
if the proposed fence fails to comply with any applicable provision
of this section or any other applicable ordinance, statute, rule or
regulation. The Town Board may also disapprove a permit for security
fencing if the proposed design or materials are inconsistent with
the character of the property or surrounding area.
[Amended 9-20-2022 by Ord. No. 2022-25]
(2)
Security fences shall not exceed eight feet in height.
H.
Prohibited fences:
(1)
Electric fences, unless erected for agricultural use where the agricultural
use is allowed.
(2)
Barbed or razor wire fences, unless erected for agricultural use
where the agricultural use is allowed or for industrial use in an
industrial district. Barbed or razor wire for industrial use shall
be permitted only above six feet above the grade and shall not extend
beyond the outer face of the fence.
(3)
Fences with dangerous protrusions, including, but not limited to,
spikes, nails, or broken glass, attached or embedded in any part of
the fence.
(4)
Fences constructed contrary to this section.
I.
Fences exempt from permit requirement. The following fences, under
the conditions set forth herein, may be erected without issuance of
a permit. All fences shall comply with all other requirements of this
chapter. A permit may still be required under other ordinances.
(1)
Temporary snow fences erected to restrict windblown snow. Such fences
shall not be erected prior to November 15 and must be removed by April
15.
(2)
Temporary construction fences for erosion control, site protection
or protection of plantings. Such fences shall be maintained for no
longer than 180 days or, if for erosion control, until the soil is
stabilized.
(4)
Fencing required for the keeping of chickens on residential property under § 135-11V, provided that the height does not exceed four feet and the total ground area does not exceed 100 square feet.
(5)
Agricultural fences used to provide enclosure for agricultural animals
or fields located in districts where agricultural uses are allowed
and not greater than 40% opaque.
(6)
Underground pet containment systems.
(7)
Earth mounds and berms, no higher than 12 inches above original grade
level, used for decorative purposes only and not part to a fence design.
(8)
Decorative fences not exceeding two feet in height.
A.
General.
(1)
Permit required. A zoning permit, to be issued by the Town Zoning
Administrator, shall be required for all berms or changes in topography
regardless of zoning district, uses, or application.
[Amended 5-17-2022 by Ord. No. 2022-10]
(2)
Review and approval.
[Amended 5-17-2022 by Ord. No. 2022-10]
(a)
Completeness. Within 10 business days of the receipt of a permit
application, the Zoning Administrator shall inform the applicant of
its completeness or the need for additional information.
(b)
Evaluation. All permits for an earthen berm shall be reviewed
by the Zoning Administrator, Public Works Director, and Town Engineer.
Written findings shall be provided to indicate compliance or noncompliance
of the application with the requirements outlined herein.
(c)
Decision. Within 30 business days of the receipt of a complete
permit application, unless action by the Zoning and Planning Commission
and/or Town Board is required, the Zoning Administrator shall inform
the applicant in writing whether the permit is approved or disapproved.
(3)
Plans and attachments.
(a)
Name, address and telephone number of the applicant, and location
of building, structure, or lot where the berm is to be constructed.
(b)
Name of person, firm, corporation, or business that is constructing
or altering the berm.
(c)
Written consent of the owner or lessee of the land upon which
the berm is proposed to be located.
(d)
Site plan depicting berm location, property lines, setbacks,
proposed and existing grade contours, any related drainage facilities,
and any existing easements on the subject property.
(e)
Proposed type of fill material and cover material.
(f)
Landscaping plan including grasses or ground cover, shrubbery,
and tree types specifying the spacing and size of all plantings.
(g)
Proposed schedule for all phases of work.
(h)
Additional information that may be unique to the property, as
required by Town staff.
[Amended 5-17-2022 by Ord. No. 2022-10]
(4)
Design.
(a)
Berms shall be designed and landscaped to minimize erosion with
a rounded crown at the highest point of the berm, extending the length
of the berm.
(b)
Berm slopes shall be protected with sod, seed, shrubs or other
form of natural ground cover. Berms adjacent to public rights-of-way
shall be a slope no greater than 3:1, unless approved by the Town
Engineer.
(c)
Trees should not be planted at the very top of a berm. Rather,
they should be planted on the slope side of a berm.
(d)
Berms should be designed carefully to blend in with the surrounding
environment. The gradient on berms should fluctuate in order to repeat
characteristics found in nature.
(5)
Height.
(a)
Maximum allowed. The height of a berm shall not exceed six feet
unless otherwise specified in this section.
(b)
How measured. The vertical height shall be measured from an
average of the existing ground grade along both sides of the berm
to the top or crown of the proposed berm.
(c)
Fencing atop a berm. Fencing shall not be placed on a berm unless
approved by the Zoning and Planning Commission. Where a berm is constructed
and/or grading is done solely to increase the effective height of
a fence, the fence's height shall be measured from the ground elevation
prior to the change in topography.
(6)
Location.
(a)
Berms shall not be located within any existing or future public
road right-of-way, utility easements or drainage easements.
(b)
A berm may straddle a lot line if a landscape easement is recorded
and attached as a deed restriction to the properties, including an
owner's agreement and easement to be provided to the Town prior to
issuance of any permit.
(7)
Grading and drainage.
(a)
Berms shall not be permitted to adversely alter stormwater drainage patterns to neighboring property owners. The Zoning Administrator and/or Town Engineer may require engineering reports, including information required under Chapter 36 of the Ledgeview Code of Ordinances, in order to assess runoff and stormwater impacts.
[Amended 5-17-2022 by Ord. No. 2022-10]
(8)
Inspection.
(a)
Berms shall be inspected by the Building Inspector, Department
of Public Works staff or Town Engineer. If berm development or berm
activities are being carried out without a permit, Town personnel
shall enter the land pursuant to the provisions of §§ 66.122
and 66.123, Wis. Stats.[1]
[Amended 5-17-2022 by Ord. No. 2022-10]
[1]
Editor's Note: Section 66.122 was renumbered as § 66.0119
and amended by 1999 Act 150, §§ 287 to 290, effective
1-1-2001; § 66.123 was renumbered in part and repealed in
part by 1999 Act 150, §§ 291, 292, effective 1-1-2001.
(b)
It is the responsibility of the property owner to exhibit that
the berm has been constructed in accordance with the approved permit,
which may necessitate documentation from a registered land surveyor
or professional engineer.
(9)
Fees. A fee, established by the Town Board, may be required
for permits and review by Town personnel and/or the Zoning and Planning
Commission.
C.
Screening for nonresidential, multifamily residential, and institutional/conservancy
properties.
(1)
Applicability. This subsection shall apply to properties with
a commercial, industrial, multifamily residential, and institutional/conservancy
use or zoning, except where they abut a property zoned or used for
single- or two-family residential.
(2)
Height. A maximum height of eight feet is permitted by right.
A height up to 10 feet may be permitted if approved by the Zoning
and Planning Commission and Town Board.
D.
Screening between residential and nonresidential land uses.
(1)
Applicability. That portion of any business, industrial, institutional,
conservancy or multiple-family district (other than duplex construction)
that is abutting property zoned or used for single-family residential
development.
(2)
Height. Earthen berms used as screening in transitional yards
shall have a minimum height of four feet. Such berm shall not exceed
10 feet in height unless approved by the Zoning and Planning Commission
and Town Board.
E.
Screening along Interstate 43 or railroad right-of-way.
(1)
Applicability. This section shall apply to any property, regardless
of zoning district, which directly abuts the right-of-way for Interstate
43 or a railroad.
(2)
Location. A berm constructed to buffer noise, light and related
impacts associated with the interstate or railroad must be located
adjacent and parallel to the right-of-way.
(3)
Height. Earthen berms used as screening in transitional yards
shall have a maximum height of 12 feet unless otherwise approved by
the Zoning and Planning Commission and Town Board.
A.
Every outdoor swimming pool, hot tub or spa, herein referred to as
"pool," having a depth of 18 inches or more, shall be surrounded by
a barrier no less than 48 inches in height above grade to restrict
unauthorized access. No barrier shall be required if the pool is equipped
with a safety cover complying with ASTM F1346 which is closed when
not in use.
B.
Permit required. No person shall construct, erect, extend, modify
or otherwise install any pool and its required barrier within the
Town of Ledgeview without first obtaining a permit from the Zoning
Administrator. Any pool in existence on the date this chapter becomes
effective shall, within 30 days from the effective date, enclose the
pool with a barrier meeting the requirements of this chapter.
[Amended 5-17-2022 by Ord. No. 2022-10]
C.
Location.
[Added 10-18-2022 by Ord. No. 2022-31[1]]
D.
Pools shall be considered structures and meet all related requirements
in the districts in which they are located.
[Amended 10-18-2022 by Ord. No. 2022-31]
E.
Any structure installed related to a pool, including but not limited
to decks and stairs, shall meet the relevant Wisconsin codes and not
obstruct the minimum barrier requirements.
F.
The required barrier height may be accomplished by including the sidewall height above grade of an aboveground pool and properly installed pool manufacturer-approved enclosure extensions as needed. Pool access shall meet the requirements of § 135-16H.
G.
The required barrier surrounding a pool is permitted to include permanent
fences and permanent structures meeting the minimum requirements,
including but not limited to dwellings, garages and accessory buildings.
H.
The required barrier surrounding the pool shall be so constructed
as not to have openings, holes or gaps that allow a four-inch-diameter
object to pass through.
I.
All entry points into the barrier shall have gates or doors equipped
with self-closing and self-latching devices placed a minimum of 50
inches above the finished grade unless otherwise constructed to be
automatically inaccessible to small children. Doorways leading from
a dwelling or accessory building to the enclosed area are exempt from
this requirement.
J.
No pool or the associated equipment, including but not limited to
motors, pumps and lighting, shall be located, designed, operated or
maintained so as to interfere unduly with adjoining property owner's
enjoyment of their property or the neighborhood. All pool motors and
pumps shall be located to minimize noise disturbance.
K.
Lights used to illuminate any pool shall be so arranged and shaded
as to reflect light away from adjoining premises. Lights shall not
create illuminations brighter than 0.5 footcandle on adjoining properties
measured at ground level.
L.
It shall be unlawful for any person to make, continue or cause to
be made or continued at any pool any loud, unnecessary or unusual
noise or any noise which annoys, disturbs, injures or endangers the
comfort, repose, health, peace or safety of others. In the operation
of a pool, the use, or permitting the use or operation, of any radio,
receiving set, musical instrument, phonograph or other machine or
device for the producing or reproducing of sound in such manner as
to disturb the peace, quiet and comfort of the neighboring inhabitants,
or at any time with louder volume than is necessary for convenient
hearing of the person or persons who are in the pool premises, shall
be unlawful.
Semitrailers and truck bodies shall only be allowed to be stored
in the open in a Heavy Industrial District or in an A-1 District on
parcels 35 acres or greater, then only as a conditional use.
A.
SEXUALLY ORIENTED ADULT ENTERTAINMENT ESTABLISHMENTS
(1)
(2)
(3)
(4)
(5)
(6)
(a)
(b)
(c)
(7)
(8)
(9)
(a)
(b)
(c)
(10)
SPECIFIED ANATOMICAL AREAS
SPECIFIED SEXUAL ACTIVITIES
Definitions. For the purpose of this section, the following terms
shall have the meanings indicated:
Includes bookstores, motion-picture theaters, mini motion-picture
theaters, bath houses, motel, modeling studios, body painting studios,
cabarets and novelty shops; and are more specifically defined as:
ADULT BOOKSTOREAn establishment having as a substantial or significant portion of its stock and trade in books, magazines and other periodicals which are distinguished or characterized by their emphasis on matter depicting, describing or relating to specified sexual activities or specified anatomical areas, as defined herein.
ADULT MOTION-PICTURE THEATERAn enclosed building with a capacity of 50 or more persons at which a significant or substantial portion of the material presented is distinguished or characterized by an emphasis on matter depicting, describing or relating to specified sexual activities or specified anatomical areas, as defined herein, for observation by patrons therein.
ADULT MOTION-PICTURE THEATER (OUTDOOR)A parcel of land from which individuals may view a motion picture presented out of doors which presents material distinguishably characterized by an emphasis on matter depicting, describing or relating to specified sexual activities or specified anatomical areas.
ADULT MINI MOTION-PICTURE THEATERAn enclosed building with a capacity for less than 50 persons used for presenting material distinguished or characterized by an emphasis on matter depicting, describing or relating to specified sexual activities or specified anatomical areas, as defined herein, for observation by patrons therein.
ADULT BATH HOUSEAn establishment or business which provides the service of baths of all kinds, including all forms and methods of hydrotherapy, that is not operated by a medical practitioner or a professional physical therapist licensed by the State of Wisconsin, and which establishment provides to its patrons an opportunity for engaging in specified sexual activities, as defined in this chapter.
ADULT MOTELA hotel, motel or similar commercial establishment which:
Offers accommodations to the public for any form of consideration;
provides patrons with closed-circuit television transmission, films,
motion pictures, video cassettes, slides or other photographic reproductions
which are characterized by the depiction or description of specified
sexual activities or specified anatomical areas; and has a sign visible
from the public right-of-way which advertises the availability of
this adult type of photographic reproductions;
Offers a sleeping room for rent for a period of time that is
less than 10 hours; or
Allows a tenant or occupant of a sleeping room to subrent the
room for a period of time that is less than 10 hours.
ADULT MODELING STUDIOAn establishment or business which provides the services of modeling for the purpose of reproducing the human body wholly or partially in the nude by means of photography, painting, sketching, drawing or otherwise.
ADULT BODY PAINTING STUDIOAn establishment or business wherein patrons are afforded an opportunity to paint images on a body which is wholly or partially nude. For purposes of this chapter, the adult body painting studio shall not be deemed to include a tattoo parlor.
An establishment or business which features male and/or female
topless and/or bottomless dancers, go-go dancers, exotic dancers,
strippers or similar entertainers.
Any adult cabaret, as defined above, which features such entertainment
on a periodic and infrequent basis is considered an adult entertainment
establishment only during those times when the adult entertainment
is being presented or the entertainers are on the premises; and all
provisions of this chapter shall apply during those presentations.
The establishment shall notify the Brown County Sheriff's Department
at least 24 hours prior to the date on which such adult entertainment
is to take place.
Any periodic adult establishment, as defined above, shall be
licensed yearly in accordance with the licensing provision hereinafter
set forth.
ADULT NOVELTY SHOPAn establishment or business having as a substantial or significant portion of its stock and trade in novelty or other items which are distinguished or characterized by their emphasis on, or designed for, specified sexual activities, as defined herein, or simulating such activity.
B.
General standards. Sexually oriented adult entertainment establishments
(hereinafter "adult establishments") shall locate only in areas zoned
Heavy Industrial (HI), and then only as a conditional use. Such application
for conditional use may only be granted if the following requirements
are met:
(1)
No more than one adult establishment shall be located on any one
parcel, and such adult establishment shall be at least 1,500 feet
from any other adult establishment. Further, no adult establishment
shall be permitted within 1,000 feet of the following:
(a)
Any land zoned residential (R-1, R-1-2A, R-2, R-3, R-R).
(b)
A historic site identified on the National Register, or as an
adopted historic district by this chapter.
(c)
Any public or private elementary or secondary school or licensed
nursery school or day-care center.
(d)
A church or established place of worship.
(e)
A public park or parkway.
(2)
Signs advertising any of the aforementioned adult uses shall be in accordance with Article XX, Regulation of Signs, with the exception, however, that no tower or portable signs or billboards shall be permitted on the premises, and with the further exception that signs will inform only of the establishment name and address and will not depict specified sexual activities and/or specified anatomical areas as defined in this chapter, and provided further that there shall be no flashing or traveling lights located outside the building. The location and wording of such sign shall be shown on the site plan required by this chapter and submitted contemporaneously with the request for conditional use.
(3)
Adequate parking shall be provided in a lighted area in accordance with Article XXI, Off-Street Parking Requirements. Such parking provisions shall be shown on the site plan required by Town ordinance and submitted contemporaneously with the request for conditional use.
(4)
There shall be no display windows on the premises.
(5)
In the case of adult cabarets, the hours of operation shall be limited
to the same hours of operation for bars and taverns within that community
within which the district is located.
(6)
Outdoor adult motion-picture theaters are prohibited.
(7)
Prior to the granting of a conditional use permit, an inventory of
the surrounding area and population shall be made by the Town Zoning
and Planning Committee along with a study of the proposed development
and plans for the area.
(8)
All adult establishments shall be licensed in accordance with this
section pertaining to the licensing of sexually oriented adult entertainment
establishments.
A.
Purpose. The purpose of this section is to establish lighting levels
for various permitted uses that promote visual surveillance, reduce
the potential for criminal activity and prevent the unnecessary glare
of light on adjacent properties.
B.
FOOTCANDLE
LIGHT TRESPASS
LUMENS
OUTDOOR LIGHTING
SECURITY LIGHTING
Definitions. The following terms, whenever used in this section,
shall have the meanings set forth below:
The luminance on a one-square-foot surface of which there
is a uniformly distributed flux of one lumen. One footcandle is equal
to one lumen per square foot. Unless otherwise expressly provided,
footcandle measurements in this section shall refer to ground-level
measurements of luminance at fully maintained output as used rather
than initial luminance.
Light from an artificial light source that is intruding across
property boundaries.
A unit of illumination, being the amount of illumination
of a unit area of spherical surface due to a light of unit intensity
placed at the center of the sphere.
Includes, but is not limited to, floodlighting, security
lighting, event lighting, landscape lighting or the lighting of off-street
parking and loading areas, but does not include public streetlights
or traffic signals.
Any light source used to illuminate a building, structure
or property during the evening hours that seeks to deter criminal
activity.
C.
Light trespass prohibited. All areas containing outdoor lighting
shall limit light trespass onto adjacent property, when measured at
any point along a property line, to the requirements set forth below.
Compliance shall be achieved utilizing fixtures shielding, directional
control designed into fixtures, fixture locations, height, or aim
or a combination of these or other factors.
District Adjoining Subject Property
|
Maximum Light Spillage to Adjoining Lots Measured
(footcandles)
|
---|---|
A-1, A-2, R-1, R-2, R-3, R-R
|
0.20
|
NCD, B-1, B-2, LI, HI, I-1, C-1, PDD-BP
|
0.50
|
D.
Neon lighting. Light sources consisting of glass tubes filled with
neon, argon, krypton, or other similar gas, hereafter referred to
as "neon lighting," are excluded from shielding and line-of-sight
requirements. Such lighting shall, however, be subject to the light
trespass requirements of § 136-18.1C.
[Added 10-7-2019 by Ord. No. 2019-18]
A.
Licensing.
(1)
A brewery shall be licensed as outlined in § 125.29(1),
Wis. Stats. 2. 3. 4.
(2)
A manufacturer or rectifier shall be licensed as outlined in § 125.52,
Wis. Stats.
(3)
A winery shall be licensed as outlined in § 125.53, Wis.
Stats.
(4)
Off-site retail premises established by manufacturers of intoxicating
liquors shall be licensed as outlined in § 125.51, Wis.
Stats.
D.
Restaurants
in breweries, manufacturers and rectifiers, or wineries. The following
criteria will apply to any restaurant use:
(1)
In industrial districts, the restaurant shall be limited to a maximum
size of 50% of the total floor area of the facility, excluding the
area devoted to the taproom, any outdoor seating area, or areas for
retail sales of items other than intoxicating beverages.
[Added 10-7-2019 by Ord. No. 2019-18]
As enabled under § 125.10 and § 125.295,
Wis. Stats., brewpubs shall meet the following requirements:
[Added 5-4-2020 by Ord. No. 2020-05]
A.
Outdoor
storage uses and areas.
(1)
Open storage of commodities shall be permitted as an accessory use,
provided that such open storage shall:
(a)
Be clearly depicted and labeled on an approved site plan, and observe
all setback requirements specified for the zoning district in which
the property is located.
(b)
Have a maximum height not to exceed the height of the main building.
(c)
Not exceed 20% lot coverage of the lot area which lies behind the
principal structure.
(d)
Be screened from view from any street or any adjacent zoned lot,
with screening surface which is 95% opaque. Screening shall consist
of landscaping, walls, fencing, berms or other methods sufficient
in density and height to mitigate sight lines and noise as much as
practicable from adjacent properties, streets, or publicly accessible
open spaces.
(e)
Surfacing.
[1]
Commercial zoning districts. All storage areas must be on a paved
(asphalt or concrete) surface.
[2]
Industrial districts. The storage of manufacturing or construction
equipment, raw materials, or finished products manufactured/assembled
on-site may be permitted on a gravel or stone surface if approved
as a conditional use by the Zoning and Planning Commission and the
Town Board. This provision shall not apply to self storage/mini-warehouse
facilities, general storage of materials not manufactured on the property,
or parking of vehicles.
(2)
Parking or storage of commercial vehicles shall not be permitted
in the front of the principal structure.
(3)
The standards referred to in Subsection A(1) above shall not apply to a commercial nursery or greenhouse
(4)
Nothing in this section shall be deemed to prohibit temporary open
storage of merchandise for display and sale during a sidewalk sale
as approved by the Town.
B.
Outdoor
sales and display areas. This section regulates permanent outdoor
sales and product display areas on commercial and industrial zoned
properties. Such sales and display areas shall conform to the following
requirements:
(1)
Outdoor sales and product display area shall be permitted by conditional
use in accordance with Section 10-9-22.
(2)
Exterior sales and display areas shall be permitted only where clearly
depicted on the approved site plan. Such demarcated areas shall not
exceed 200 square feet in area. Outdoor sales or display shall be
conducted only within the designated area. Such areas shall be not
considered part of a required greenspace area.
(3)
Outdoor sales shall not be conducted within 50 feet of any residential
zoning district unless screened from view.
(4)
All sales and display areas must be on a paved (asphalt or concrete)
surface unless otherwise approved by the Zoning and Planning Commission
and the Town Board.
(5)
Outdoor sales and display areas shall be maintained in an orderly
manner, free of litter and other refuse.
(6)
Storage of goods for sale shall be no more than five feet in height.
Outdoor sales or displays shall not obstruct access to buildings or
parking spaces on the site, or to adjoining property.
C.
Automobile sales facilities. The standards referred to in Subsection A or B above, with the exception of the surfacing requirement, shall not apply to new or used automobile dealer facilities which have outdoor display of vehicles for sale. Such display of vehicles shall be permitted as an accessory use to a dealer facility which shall be approved as part of the overall approval of a site plan for an automobile facility.