[Adopted 11-21-1983 by L.L. No. 28-1983]
No person shall tap or make a connection with
a water main of the Village of Old Westbury without a written permit
from the Village Clerk.
[Amended 8-18-2008 by L.L. No. 3-2008; 10-17-2016 by L.L. No. 11-2016]
A fee for each tap or service line connection of $350 shall
be paid to the Village Clerk, plus the amounts as per the following
schedule:
Size
(inches)
|
Fee
|
---|---|
1
|
$500
|
1Â 1/2
|
$800
|
2
|
$1,000
|
4
|
$1,500
|
6
|
$3,500
|
8
|
$4,500
|
No person to whom a permit shall have been issued,
or his or its agents, servants or employees, shall make a tap or connection
to a Village water main without the presence of an employee of the
Village designated to inspect the work.
No tap or connection to a Village water main
shall be made except between the hours of 9:00 a.m. and 3:00 p.m.,
Monday through Friday, except holidays.
All taps and connections to Village water mains
shall be made in good and workmanlike manner. The permittee shall
be responsible for and shall replace, on demand of the Superintendent
of Water Supply of the Village, any tap or connection which may be
found by the Village not to conform to this section, even though previously
inspected by the Village. Shall the permittee fail to replace any
such tap or connection, the Village shall make such replacements or
repairs as shall be necessary at the cost and expense of the permittee.
All service lines between the water main and meter pit shall at all
times be kept in serviceable condition by the property owner. Upon
proper notification by the Village to the property owner of the fact
that a faulty service exists, the Village may, after reasonable time,
have the repairs made at the expense of the owner.
The permittee shall indemnify and save harmless
the Village of Old Westbury, its officials, servants and employees
from all action or proceedings, including the defense thereof, to
recover damages for injuries to persons or property recovered by or
through the permittee, its agents, servants and employees in connection
with tapping and connecting with water mains of the Village of Old
Westbury.
To secure the presence of a Village inspector on the job, at least 24 hours' notice shall be given to the Superintendent of Water Supply. Failure of an inspector to present himself at the time and place requested shall not be deemed a waiver by the Village of the requirement contained in § 210-17 hereof.
Shall any tap or connection be made without
the presence of a Village inspector, the permittee shall be required
to expose the tap or connection, or if the permittee shall refuse,
such tap or connection may be exposed for inspection by the Village
at the cost and expense of the permittee.
No permit shall extend beyond 15 days.
[Amended 6-19-2017 by L.L. No. 5-2017]
A.Â
All service lines shall be not less than 3/4 inch inside diameter
and shall be of Type K copper. All connections shall be compression
connections. The service line is considered to be the water service
pipe extending from the water main in the street to the inside of
the building and shall consist of the corporation stop, saddle (if
required), curb box, meter pit, meter pit cover meter, meter valves,
backflow preventor and pipe. One plug valve shall be installed on
each side of the meter in all cases and each side of the backflow
preventor. No service line shall be installed in a driveway, and shall
at all times conform to the regulations of the Nassau County Board
of Health with respect to any cesspools or sewer lines thereto, or
less than four feet below finish grade or more than five feet below
finish grade.
B.Â
Meters shall be Badger meters with straight gallon registers. Badger
meters may be purchased from local supply houses.
Taps and connections to any Village water main
shall be as follows:
In all service lines up to and including one
inch, there shall be a stop cock of the inverted-key type at a point
one foot outside the property line and provided with an iron box,
rod and cover. In the case of all service lines of 1Â 1/4 inches
and over, a ball valve of the type manufactured by Eddy Valve Company
or equal shall be used.
[Amended 6-19-2017 by L.L. No. 5-2017]
A.Â
Each meter under 1Â 1/2 inches shall be installed in a meter
pit consisting of a twenty-four-inch round poly or concrete or equal
with iron cover. The cylinder shall be inserted to a depth of four
feet below finished grade and shall rest on at least three bricks.
The cover of the pit shall be constructed and be maintained one inch
above finished grade. The meters shall be 14 inches below the cover
with a valve on each side, and the risers on each side of the meter
shall be a least two inches from the side walls of the meter pit.
Each meter 1Â 1/2 inches and over shall be installed in a meter
pit not less than three feet by five feet and the bottom not to be
more than five feet below finished grade and in all cases large enough
to permit a man to descend into the pit and work around the meter.
Such meter pit shall be poly constructed or poured concrete or solid
concrete block and shall have a reinforced concrete roof with a metal
manhole cover not less than 24 inches and not greater than 36 inches
in diameter.
B.Â
All meter pits shall be located two feet inside of the property line.
All water services must be installed by a licensed
plumber or contractor approved by the Board of Trustees of the Village
or the appropriate administrative official.
[Amended 9-20-1993 by L.L. No. 4-1993]
No water shall be taken from any hydrant without the written permission of the Board of Trustees of the Village or the appropriate administrative official. In the event that such permission is granted, the fee shall be in the amount set forth in Chapter 103, Fees and Deposits.
[Amended 6-18-2007 by L.L. No. 2-2007]
A.Â
Each meter shall be inspected, rebuilt or replaced
once every 10 years from the date of installation. The Water Department
reserves the right to remove, test and repair any meter at any time.
If requested by an owner to test any meter, the cost of repairs, if
any, shall be borne by the owner. If the meter is found to be accurate
according to New York State Standards and Requirements, a charge of
$25 shall be made. If the meter is found to be inaccurate, no charge
for the test shall be made; however, the cost of repairs shall be
borne by the owner for all meters two inches and under.
B.Â
The use of submetering in the Village of Old Westbury is hereby prohibited. Each home in the Village shall have its own separate water supply and be metered and be billed by the Village. The Superintendent of Water may waive this requirement or grant relief from this requirement in circumstances where compliance is not feasible or where the Village does not have a water main for the homeowner to tie into. When the public water supply becomes available, it is incumbent upon the homeowner to tie into the Village main within 90 days of being notified of water availability. Such connection shall be at the homeowner's expense. If such connection is not completed within 90 days of notification of water availability, a violation may be issued for each day that such connection is not complete. Any person violating this § 210-30B shall be deemed guilty of a violation punishable by a fine of $250 for each daily violation.
Whenever it may be found that the foregoing
rules and regulations do not apply or make it impractical to install
a water service in compliance therewith, such condition shall be brought
to the attention of the Board of Trustees or appropriate administrative
official of the Village for consideration. Permission for any deviation
from these rules and regulations, if granted, shall be in writing.
[Amended 6-19-2017 by L.L. No. 5-2017]
No underground sprinkler system shall be installed within the
Village of Old Westbury without the written permission of the Board
of Trustees of the Village or of the appropriate administrative official.
In the event that such permission is granted, the fee shall be $300
for such permit. All systems shall be installed as per plans and specifications
on file at the office of the appropriate administrative official.
A.Â
The owner or his engineer shall file with the Village Clerk an application in triplicate for the installation of water mains in a subdivision, the application to be accompanied by three prints of the proposed overall development plan; a fee of $25 per acre or part thereof and a deposit of $2,000 as part of the legal, engineering and contingencies required in Subsection F below shall be paid to the Village Clerk.
B.Â
The Village Water Engineer, on receipt of the development
plan, will indicate thereon the required water mains and appurtenances
and file the plan with the Board of Trustees.
C.Â
After the plan has been approved by the Planning Board
or administrative official, one copy will be filed with said Board,
one copy with the Village Water Engineer and one copy to be returned
to the owner.
D.Â
Before the owner is ready to file his map with the
Department of Health or, if the Department of Health approval is not
required, with the appropriate authority, he shall furnish the Village
Water Engineer with four copies of the proposed map on which will
be indicated the size of the water mains and appurtences in accordance
with the prior approval of the Board of Trustees. One copy will be
filed with the Board of Trustees, one copy with the Village Water
Engineer and two copies furnished to the owner.
E.Â
When the owner is ready to have water mains installed,
an application therefor shall be filed with the Village Clerk, to
be accompanied by a minimum fee of $500 for the first 500 feet or
any part thereof and an additional $25 per 100 feet or part thereof
in excess of 500 feet. The Village Water Engineer shall then prepare
a plan for the same, together with specifications, bidding sheet,
etc. Said engineer will prepare the advertisement for bids, and, at
the specified time the bids will be opened, and thereafter a contract
awarded by the Board of Trustees as hereinafter provided.
F.Â
Before the contract has been awarded and within 15
days after the opening of bids, the owner shall deliver to the Village
an instrument dedicating to the Village a perpetual easement for the
construction and maintenance of water mains and appurtenances thereto,
over and under the land of the owner as shown on the plan, in a form
satisfactory to the Village Attorney, to be recorded in the Nassau
County Clerk's office, together with satisfactory title company certificates
showing the instrument to be executed by all owners and mortgagees
and other lienors, and will deposit a certified check with the Village
in an amount which the Village shall require to install the mains,
plus 20% to cover necessary expenses for legal, engineering and contingencies.
At the same time, the owner will enter into a contract with the Board
of Trustees for the execution of the work, pursuant to which contract
the owner will enter into a contract with the contractor to whom the
award has been made by the Board of Trustees.
G.Â
The water mains will be installed under the supervision
of the Village Water Engineer and the Superintendent of Public Works,
and upon completion, said Engineer will prepare an estimate of the
completed work. The amount, plus engineering and legal fees, will
be paid by the Board of Trustees from moneys deposited by the owner.
H.Â
Before the Village will undertake to take over such
water system so installed in private subdivisions, undertake to keep
such water system in operation and repair and before any refunds of
the amounts deposited are made, the Village must be furnished satisfactory
proof that either the streets in which the water mains are laid have
been dedicated and accepted by proper public authority or instruments
granting easements to the Village, in form satisfactory to the Village
Attorney to be recorded in the Nassau County Clerk's office, with
a satisfactory title company certificate showing the same to have
been executed by all owners and mortgagees and other lienors, shall
have been delivered to the Village and that all valve boxes have been
located and placed at the right levels.
I.Â
Upon satisfactory completion of the installation of
the water mains and appurtenances thereto and compliance with this
section and the subdivisions thereof, the Engineer designated by the
Village will then advise the Board of Fire Underwaters accordingly.
A.Â
Whenever water rent shall remain unpaid for 30 days
or more after becoming due, the supply of water to premises upon which
said water rent is a lien shall be cut off upon 10 days' notice thereof
by the Village Clerk, mailed to the person against whom the premises
are assessed or to the person designated by the owner to whom bills
shall be sent by the Village Clerk.
B.Â
No premises shall, after water has been cut off, receive
water until the water bill, together with the cost of cutting off
and turning on the water, has been paid.
C.Â
All bills for water and service charges are due and
payable when rendered. A penalty of 5% for the first month and 1/2
of 1% for each additional month of the amount due shall be added to
all unpaid water and service charges which are in arrears for one
month or longer.
D.Â
Whenever the owner and/or occupant of premises shall
fail or refuse to comply with any of the Village of Old Westbury Rules
and Regulations of the Water Department as last amended by the Board
of Trustees on December 2, 1955, or as the same may be revised, altered
or amended,[1] the supply of water to the premises shall be cut off upon
10 days' notice thereof by the Village Clerk and mailed to the person
against whom the premises are assessed or to the person designated
by the owner to whom a bill shall be sent by the Village Clerk.
[1]
Editor's Note: Said Rules and Regulations
are available in the office of the Village Clerk.
E.Â
No premises shall, after water has been cut off, receive
water until the cost of cutting off and turning on the water has been
paid.
A.Â
Responsibility of the Board of Trustees. The Board
or administrative official, if so appointed, shall inspect the plumbing
in the Village at prescribed intervals to ensure that such plumbing
was installed and is maintained in such a manner as to safeguard the
potable water supply by preventing backflow into the potable water
supply system. The Board or administrative official, if so appointed,
shall notify or cause to be notified in writing the owner or authorized
agent of the owner of any such building or premises to correct, within
a reasonable time set by the Board, any plumbing installed or existing
contrary to or in violation of this article and which in its judgment
may, therefore, permit the pollution of the Village water supply or
otherwise adversely affect the public health.
B.Â
Inspection. The Board or administrative official,
if so appointed, shall have the right of entry into any building during
reasonable hours for the purpose of making inspections of the plumbing
systems installed in such building or premises, provided that with
respect to the inspection of any single-family dwelling, consent to
such inspection shall first be obtained from a person of suitable
age and discretion therein or in control thereof.
When used in this article, unless otherwise
indicated, the following words shall have the following meanings:
The unobstructed vertical distance through the free atmosphere
between the lowest opening from any pipe or faucet supplying water
to a tank, plumbing fixture or other device and the flood level rim
of the receptacle.
Accepted by the Board and by the Department of Health where
required an applicable specification, stated or cited in this article
or as suitable for the proposed use.
Any water source or system other than the Water District
water supply, which may be available in the building or on the premises.
The flow of water or other liquids, mixtures or substances
into the distributing pipes of a potable supply of water from any
source or sources other than its intended source.
A device or means to prevent backflow.
Backflow resulting from negative pressures in the distributing
pipes of the potable water supply.
A loop of pipe rising approximately 35 feet, at its topmost
point, above the highest fixture it supplies.
The Board of Trustees of the Incorporated Village of Old
Westbury.
A self-closing device which is designed to permit the flow
of fluids in one direction and to close if there is a reversal of
flow.
See "pollution."
Any physical connection between a potable water supply and
any waste pipe, soil pipe, sewer, drain or any unapproved source or
system. Furthermore, it is any potable water supply outlet which is
submerged or can be submerged in waste water and/or any other source
of contamination. (See "backflow" and "back siphonage.")
Any pipe which carries waste-water or waterborne wastes in
a building drainage system.
Installed receptacles, devices or appliances supplied with
water or which receive or discharge liquids or liquid-borne wastes.
The edge of the receptacle from which water overflows.
Any conditions, devices or practices in the water supply
system and its operation which create or, in the judgment of the Board,
may create a danger to the health and well-being of the water consumer.
An example of a health hazard is a structural defect in the water
supply system, whether of location, design or construction, which
may regularly or occasionally prevent satisfactory purification of
the water supply or cause it to be polluted from extraneous sources.
Any arrangement of plumbing, including piping and fixtures
whereby a cross-connection is created.
A pressure vessel in which air pressure acts upon the surface
of the water contained within the vessel, pressurizing the water distribution
piping connected to the vessel.
The open end of the water supply pipe through which the water
is discharged into the plumbing fixture.
Includes the water supply and distribution pipes, plumbing
fixtures and traps; soil, waste and vent pipes; building drains and
building sewers, including their respective connections, devices and
appurtenances within the property lines of the premises; and water-treating
or water-using equipment.
The presence of any foreign substance (organic, inorganic,
radiological or biological) in water which tends to degrade its quality
so as to constitute a hazard or impair the usefulness of the water.
An assembly of differential valves and check valves, including
an automatically opened spillage port to the atmosphere designed to
prevent backflow.
The receiving, nonpressure vessel forming part of the air
gap separation between a potable and an auxiliary supply.
Any pressure less than that exerted by the atmosphere.
A vacuum breaker which is designed so as not to be subjected
to static line pressure.
A vacuum breaker designed to operate under conditions of
static line pressure.
The Incorporated Village of Old Westbury.
Water which is not safe for human consumption or which is
of questionable potability.
Any water which complies with the provisions of Part 72 of
the Title 10 of the New York Codes, Rules and Regulations (drinking
water standards) of the administrative rules and regulations of the
New York State Commissioner of Health.
A potable water supply system shall be designed,
installed and maintained in such manner as to prevent contamination
from nonpotable waters, liquids, solids or gases from being introduced
into the potable water supply through cross-connections or any other
piping connections to the system.
Cross-connections between potable water systems
and other systems or equipment containing water or other substances
of unknown or questionable safety are prohibited, except when and
where, and as approved by the New York State Commissioner of Health
pursuant to Section 5.33 of the New York State Sanitary Code, suitable
protective devices such as the reduced-pressure zone backflow preventer
or equal are installed, tested and maintained to ensure proper operation
on a continuing basis.
Interconnection between two or more public water
supplies shall be permitted only with the written approval of the
Board and the New York State Department of Health.
Cross-connections between an individual water
supply and a potable public supply are prohibited unless approved
in writing by the Board and the New York State Department of Health.
Potable water connections to boiler.feed water
systems shall be made through an air gap or provided with an approved
back-flow preventer (reduced pressure principle or double check-double
gate valves).
Connection to the potable water supply system for the following is prohibited unless protected against backflow in accordance with § 210-43 or as set forth as follows:
A.Â
Bidets.
B.Â
Operating, dissection, embalming and mortuary tables
or similar equipment. In such installation the hose used for water
supply shall terminate at least 12 inches away from every point of
the table or attachments.
C.Â
Pumps for nonpotable water, chemicals or other substances.
Priming connections may be made only through an air gap.
D.Â
Building drainage, sewer or vent systems.
E.Â
Any other fixture of similar hazard.
Except where potable water provided for a refrigerator
condenser or cooling jacket is entirely outside the piping or tank
containing a toxic refrigerant and two separate thicknesses of metal
separating the refrigerant from the potable water supply, an inlet
connection shall be provided with an approved check valve. Also adjacent
to and at the outlet side of the check valve, an approved pressure
relief valve, set to relieve five pounds per square inch above the
maximum water pressure at the point of installation, shall be provided
if the refrigeration units contain more than 20 pounds of refrigerants.
A.Â
Water outlets. A potable water system shall be protected
against backflow and back siphonage by providing and maintaining at
each outlet:
(1)Â
Air gap. An air gap as specified in Subsection B between the potable water outlet and the flood level rim of the fixture it supplies or between the outlet and any other source of contamination; or
(2)Â
Backflow preventer. An approved backflow preventer
device or vacuum breaker to prevent the drawing of contamination into
the potable water system.
B.Â
Minimum required air gap.
(1)Â
How measured. The minimum required air gap shall be
measured vertically from the lowest end of a potable water outlet
to the flood rim or line of the fixture or receptacle into which it
discharges.
(2)Â
Size. The minimum required air gap shall be twice
the effective opening of a potable water outlet, unless the outlet
is a distance less than three times the effective opening away from
a wall or similar vertical surface, in which case the minimum required
air gap shall be three times the effective opening of the outlet.
In no case shall the minimum required air gap be less than shown in
the following table, Minimum Air Gaps For Generally Used Plumbing
Fixtures.
MINIMUM AIR GAPS FOR GENERALLY USED
PLUMBING FIXTURES
| ||
---|---|---|
Fixture
|
Minimum Air Gap When Not Affected by Near
Wall1
(inches)
|
When Affected by Near Wall2
(inches)
|
Lavatories and other fixtures with effective
openings not greater than 1/2-inch diameter
|
1.0
|
1.50
|
Sink, laundry trays, gooseneck bath faucets
and other fixtures with effective openings not greater than 3/4-inch
diameter
|
1.5
|
2.25
|
Over rim bath fillers and other fixtures with
effective openings not greater than 1-inch diameter
|
2.0
|
3.0
|
Drinking water fountains (single orifice) 7/16-inch
(0.437-inch) diameter or multiple orifices having total area of 0.150
square inch (area of circle 7/16-inch diameter)
|
1.0
|
1.50
|
Effective openings greater 1-inch
|
3
|
4
|
NOTES:
|
---|
1 Side walls, ribs
or similar obstructions do not affect air gaps when spaced from the
inside edge of the spout opening a distance greater than three times
the diameter of the effective opening for a single wall or a distance
greater than four times the diameter of the effective opening for
two intersecting walls.
|
2 Vertical walls,
ribs or similar obstructions extending from the water surface to or
above the horizontal plane of the spout opening require a greater
air gap when spaced closer to the nearest inside edge of spout opening
than specified in Note 1 above. The effect of three or more such vertical
walls or ribs has not been determined. In such cases, the air gap
shall be measured from the top of the wall.
|
3 Two times the diameter
of the effective opening.
|
4 Three times the
diameter of the effective opening.
|
C.Â
Approval and testing of devices. Before any device
for the prevention of backflow or back siphonage is installed, it
shall have first been approved in writing by the Board. In addition,
Department of Health approval is required in those instances where
an air gap or control device, for which an acceptable list has been
established by the New York State Department of Health, is utilized
to protect the water supply from a hazardous substance, Devices installed
in a building's potable water supply distribution system for protection
against backflow shall be maintained in good working condition by
the person or persons responsible for the maintenance of the system.
Every owner of real property within the Village shall be responsible
for the installation, maintenance and testing of backflow prevention
devices on such property. All backflow prevention devices must be
tested annually at the direction and expense of the owner of the property.
Such testing must be performed by a backflow prevention device tester
certified by the New York State Department of Health. This testing
is mandated by New York State as an issue of public health, safety
and welfare. Every property owner must prove compliance with this
section by providing the Village Superintendent of the Water Department
with proof of such testing on or before September 1 of each year.
[Amended 11-21-2005 by L.L. No. 5-2005]
D.Â
Installation of devices.
(1)Â
Vacuum breakers. Vacuum breakers shall be installed
with one critical level at least six inches above the flood level
rim of the fixture they serve and on the discharge side of the last
control valve to the fixture. No shutoff valve or faucet shall be
installed beyond the vacuum breaker. For closed equipment or vessels,
such as pressure sterilizers, the top of the vessel shall be treated
as the flood level rim, but a check valve shall be installed on the
discharge side of the vacuum breaker.
(2)Â
Reduced-pressure-principle backflow preventer. A reduced-pressure-principle-type
backflow preventer may be installed subject to full static pressure.
(3)Â
Devices of all types. Backflow and back siphonage
preventing devices shall be accessibly located, preferably in the
same room with the fixture they serve. Installation in utility or
service spaces, provided that they are readily accessible, is also
permitted.
E.Â
Tanks and vats below rim supply.
(1)Â
Where a potable water outlet terminates below the
rim of a tank or vat and the tank or vat has an overflow of a diameter
not less than given in the following table, Sizes of Overflow Pipes
for Water Supply Tanks, the overflow pipe shall be provided with an
air gap as close to the tank as possible.
SIZES OF OVERFLOW PIPES FOR WATER
SUPPLY TANKS
| |
---|---|
Maximum Capacity of Water Supply Line
to Tank
(gallons per minute)
|
Diameter of Overflow Pipe
(inches internal diameter)
|
0-50
|
2
|
50-150
|
2Â 1/2
|
100-200
|
3
|
200-400
|
4
|
400-700
|
5
|
700-1,000
|
6
|
Over 1,000
|
8
|
(2)Â
The potable water outlet to the tank or vat shall
terminate a distance not less than 1Â 1/2 times the height to
which water can rise in the tank above the top of the overflow. This
level shall be established at the maximum flow rate of the supply
to the tank or vat and with all outlets, except the air gap overflow
outlet, closed.
(3)Â
The distance from the outlet to the high-water level
shall be measured from the critical point of the potable water supply
outlet.
F.Â
Protective devices required.
(1)Â
The design criteria for physical connection control
devices shall be as shown in the table below:
DESIGN CRITERIA FOR PHYSICAL
CONNECTION CONTROL DEVICES
| ||||||
---|---|---|---|---|---|---|
Control Devices
| ||||||
Conditions
|
Air Gap
|
Reduced Pressure Device
|
Double Check Valve Assembly
|
Atmospheric Vacuum Breaker
|
Pressure Vacuum Breaker
| |
Any physical connection which may be
subject to back pressure involving:
| ||||||
Hazardous substances*
|
x
|
x
| ||||
Nonhazardous substances**
|
x
|
x
|
x
| |||
Any physical connection not subject
to back pressure involving:
| ||||||
Hazardous substances*
|
x
|
x
|
x
|
x
| ||
Nonhazardous substances**
|
x
|
x
|
x
|
x
|
x
|
NOTES:
* A hazardous substance includes sewage,
lethal chemicals or other substances which, if introduced into the
public water supply system, would or may endanger the health of the
consumer.
** A nonhazardous substance would not
endanger the health of the consumer but would be a nuisance if introduced
into the public water supply program.
|
(2)Â
The Board shall determine the condition of the connection
in accordance with the categories listed in the above table and shall
determine what type of control device is required. Only approved devices
shall be utilized.
(3)Â
Approved devices to protect against backflow and back
siphonage shall be installed at all fixtures and equipment where backflow
and/or back siphonage may occur and where a minimum air gap cannot
be provided between the water outlet to the fixture or equipment and
its flood level rim.
(4)Â
Connections not subject to back pressure. Where a
water connection is not subject to back pressure, a nonpressure-type
vacuum breaker shall be installed on the discharge side of the last
valve on the line serving the fixture or equipment. A list of some
conditions requiring protective devices of this kind is given in the
following table, Cross-Connections Where Protective Devices are Required
and Critical Level (C-L) Settings for Vacuum Breakers.
CROSS-CONNECTIONS WHERE PROTECTIVE
DEVICES ARE REQUIRED AND CRITICAL
LEVEL (C-L) SETTINGS FOR VACUUM BREAKERS1
|
Fixture or Equipment
|
Method of Installation
|
---|---|
Aspirators and ejectors
|
C-L at least 6 inches above flood level of receptacle
served.
|
Dental units
|
On models without built-in vacuum breakers,
C-L at least 6 inches above flood level rim of bowl.
|
Dishwashing machines
|
C-L at least 6 inches above flood level of machine.
Install on both hot- and cold-water supply line.
|
Flushometers (closet and urinal)
|
C-L at least 6 inches above top of fixture supplies.
|
Garbage-can cleaning machine
|
C-L at least 6 inches above flood level of machine.
Install on both hot-and cold-water supply lines.
|
Hose outlets
|
C-L at least 6 inches above highest point on
hose line.
|
Laundry machines
|
C-L at least 6 inches above flood level of machine.
Install on both hot- and cold-water supply lines.
|
Lawn sprinklers
|
C-L at least 12 inches above highest sprinkler
or discharge outlet.
|
Steam tables
|
C-L at least 6 inches above flood level.
|
Tank and vats
|
C-L at least 6 inches above flood level rim
or line.
|
Trough urinals
|
C-L at least 30 inches above perforated flush
pipe.
|
Flush tanks
|
Equip with approved ball cock. Where ball cocks
touch tank water, equip with vacuum breaker at least 1 inch above
overflow outlets. Where ball cock does not touch tank water, install
ball cock outlet at least 1 inch above overflow outlet or provide
vacuum breaker as specified above.
|
Hose bibbs (where aspira- tors or ejectors could
be connected)
|
C-L at least 6 inches above flood level of receptacle
served.
|
NOTES:
1Critical level (C-L)
is defined as the level to which the vacuum breaker may be submerged
before backflow will occur. Where the C.L is not shown on the preventer,
the bottom of the device shall be taken as the C.L.
|
(5)Â
Connections subject to back pressure. Where a potable
water connection is made to a line, fixture, tank, vat, pump or other
equipment with a hazard of back-flow or back siphonage where the water
connection is subject to back pressure and an air gap cannot be installed,
the installation of an approved reduced-pressure-principle backflow
preventer shall be required. A partial list of such connections is
shown in the following table, Partial List of Cross-Connections Which
May Be Subject to Back Pressure.
PARTIAL USE OF CROSS-CONNECTIONS WHICH
MAY BE SUBJECT TO BACK PRESSURE
| |
---|---|
Chemical lines
| |
Dock water outlets
| |
Individual water supplies
| |
Industrial process waterlines
| |
Pressure tanks
| |
Pumps
| |
Steam lines
| |
Swimming pools
| |
Tank and vats, bottom inlets
| |
Hose bibbs
|
G.Â
Double check - double gate valves. The Board may authorize
installation of approved double check - double gate valve assemblies
with test cocks as protective devices against backflow in connections
between a potable water system and other nonhazardous substances which
would not endanger the health of the consumer but would be a nuisance
if introduced into the public water supply system.
H.Â
Low-pressure cutoff required on booster pumps. When
a booster pump is used on a water pressure booster system and the
possibility exists that a positive pressure of 10 pounds per square
inch or less may occur on the suction side of the pump, there shall
be installed a low-pressure cutoff on the booster pump to prevent
the creation of a vacuum or negative pressure on the suction side
of the pump, thus cutting off water to other outlets.
A.Â
General requirements. It shall be the responsibility
of building and premises owners to maintain all backflow preventers
and vacuum breakers within the building or on the premises in good
working order and to make no piping or other arrangements for the
purpose of bypassing backflow devices.
B.Â
Backflow preventers. These devices should be inspected
frequently after the initial installation to assure that they have
been installed properly and that debris resulting from the installation
has not interfered with the functioning of the device. The testing
procedures shall be in accordance with the manufacturer's instructions
and in compliance with all local, state and federal requirements.
Testing shall be conducted by a backflow prevention device tester
certified by the New York State Department of Health, and the devices
shall bear an inspection certification tag indicating the date of
inspection and the name and address of the backflow prevention device
tester who conducted such inspection.
[Amended 11-21-2005 by L.L. No. 5-2005]
[Amended 11-21-2005 by L.L. No. 5-2005]
A.Â
Notification of violation. When a violation of this
article is found, the Board or its administrative official, if so
appointed, shall notify, by written notice, the owner of the property,
as indicated on the then-current Village tax roll.
B.Â
Notice requirements.
(1)Â
The notice shall identify the sections of the article
that have been violated and the basis for the notice of violation.
(2)Â
The notice shall inform the owner that, should he
disagree with the conclusion as to the violation, he shall have seven
calendar days from receipt of the notice, or a shorter time period
determined by the Board of Trustees or the Superintendent of the Village
Water Department, to file a written request at the Village Hall for
a hearing on the matter before the Village Board of Zoning Appeals.
The Board or Superintendent may set a shorter time if the Board or
Superintendent determines that exigent circumstances exist, threatening
the health, safety or welfare of Village residents.
(3)Â
The notice shall inform the owner that if he does
not request a hearing and he fails to cure the violation within seven
calendar days of the receipt of the notice, or a shorter time period
determined by the Board of Trustees or the Superintendent of the Village
Water Department, the agents of the Village Water Department shall
have the right, but not the duty, to enter onto such owner's land
to perform the testing required. The Board or Superintendent may set
a shorter time period if the Board or Superintendent determines that
exigent circumstances exist, threatening the health, safety or welfare
of Village residents. In any event, the curing of the violation shall
be at the expense of the owner of the land. If the agents of the Village
Water Department perform the testing required, a fee of $250 will
be due and owing to the Village from the property owner. In the event
that the owner fails to pay the Incorporated Village of Old Westbury
$250 within 30 days after demand therefor is sent to the last address
for the owner indicated on the then-current Village tax roll, the
fee of $250 shall be added to the property's November water assessment.
(4)Â
The notice shall be given by personal delivery to
the person to be served; be given by personal delivery to a person
of suitable age and discretion at the dwelling place of the person
to be served and by first-class mail to the person to be served; or
be given by registered mail, return receipt requested, at the last
known address of the person to be served.
C.Â
Notwithstanding the foregoing, if in the Board's judgment
a health hazard exists, the Board may cause the water service to the
building or premises to be terminated.
D.Â
Fines. The owner or authorized agent of the owner responsible for the maintenance of the plumbing systems and use of water on the premises or in the buildings thereon who knowingly permits a violation of any of the provisions of this article to remain uncorrected after the expiration of the time period set forth in the notice issued pursuant to Subsection B above shall, upon conviction by the court, be subject to and required to pay a fine of not in excess of $250 for each violation, and each day of failure to comply with the requirements of this article after the expiration of the time period set forth in the notice issued pursuant to Subsection B above shall constitute a separate violation.