The purpose of this chapter is to establish a comprehensive
system of sign controls regarding the construction, installation,
and maintenance of signs that will:
A.
Promote and protect the health, safety, and welfare of the City by
ensuring the compatibility of signs with surrounding structures and
land uses.
B.
Create a more attractive business and economic climate by enhancing
and protecting the orderly and effective display of signs, and discourage
sign clutter.
C.
Protect the public from hazardous conditions that result from the
indiscriminate use and placement of signs, structurally unsafe signs,
signs that obscure the vision of pedestrians or motorists, and signs
that compete or conflict with necessary traffic signals, government
signs, and warning signs.
All signs constructed, erected, modified, or altered must comply
with the following standards.
A.
Prohibited Installations.
1.
No sign may be erected in a location that violates the building
code, fire code, and other applicable City codes or ordinances.
2.
No sign may obstruct the following sight triangles:
a.
Signs are prohibited within a thirty-foot visibility triangle
at the intersection of two streets as measured along the back of curb
or edge of roadway pavement, as applicable.
ii.
Signs are prohibited within a ten-foot
visibility triangle at the intersection of a street and an alley or
at the intersection of a street and a private driveway as measured
along the back of curb or edge of roadway pavement, as applicable,
or along the driveway edge.
iii.
Signs are prohibited within a ten-foot visibility
triangle at the intersection of two alleys as measured along the edge
of alley pavement.
3.
Only signs that have been placed by or authorized by federal,
state, or the City may be installed on public property. Any sign installed
on public property, including rights-of-way, without prior authorization,
will be removed by the City without notice and disposed of.
4.
No permanent sign may be erected on private property without
the consent of the property owner or his/her authorized agent. Any
sign installed on private property without authorization may be removed
by the property owner without notice and disposed of.
5.
No sign may be erected in a manner that obstructs access to
any ingress or egress, fire escapes, fire hydrants, fire department
connections, or standpipes and similar fire safety connections.
B.
Construction Standards.
1.
Supports and braces must either be designed as an integral part
of the overall sign or obscured from public view to the extent feasible.
2.
All signs attached to a building must be installed and maintained
so that wall penetrations are watertight and the structure does not
exceed allowable stresses of supporting materials.
3.
All signs must be designed and constructed in compliance with
the building code, electrical code, and all other applicable codes
and ordinances.
4.
All permanent signs must be constructed of rigid, weather-proof
materials.
5.
No sign may be painted on a wall or any other structure. As
of the effective date of this ordinance, existing painted on wall
signs, called ghost signs, are exempt from this prohibition. Such
signs may only be restored to the original graphic, therefore no new
information may be added to such ghost signs.
6.
Glass comprising any part of a sign must be safety glass.
7.
All letters, figures, characters, or representations in cut-out
or irregular form, maintained in conjunction with, attached to, or
superimposed upon any sign must be safely and securely built into
or attached to the sign structure.
C.
Electrical Wiring.
1.
All electrical fixtures, devices, circuits, conduits, raceways,
or similar features must be installed and maintained in compliance
with the current City electrical code.
2.
Conduits, raceways, and other components of a sign illumination
system must be designed as an integral part of the overall sign structure
and obscured from public view to the extent technically feasible.
D.
Required Maintenance.
1.
All signs must be kept in a safe and well-maintained condition
and appearance, and must be repainted or otherwise maintained by the
property owner or business owner to prevent corrosion or deterioration
caused by the weather, age, or any other condition.
2.
All signs must be maintained to prevent any kind of safety hazard,
including faulty or deteriorated sign structures, a fire hazard, or
an electrical shock hazard.
3.
All unused sign hardware or wiring must be removed.
4.
No sign frame may remain unfilled or allow any internal part
or element of the sign structure to be visible.
5.
If a sign is maintained in an unsafe or unsecured condition,
it must be removed or the condition corrected. If the sign is not
removed or the condition is not corrected within the required time
period, the City may enforce this order through permitted enforcement
procedures of Chapter 17.18.
6.
The City may remove any sign that is an immediate public peril
to persons or property summarily and without notice. The owner of
such sign is responsible for all costs of removal.
7.
Where possible by the design of a sign structure, a permanent
sign that becomes obsolete after the associated activity or use is
discontinued or abandoned must remove all sign copy from the sign
structure and the panels must be removed and replaced with a blank
panel. This requirement is not satisfied by reversing (i.e., turning
such copy so that it faces inward), painting over, covering with vinyl
or other fabric, or otherwise means of obfuscating such copy.
8.
When an electronic message sign becomes obsolete after the associated
activity or use is discontinued or abandoned, the electronic component
must be turned off.
A.
Any sign illumination, including gooseneck reflectors, external illumination,
and internal illumination, must be designed, located, shielded, and
directed to prevent the casting of glare or direct light upon roadways
and surrounding properties, and prevent the distraction of motor vehicle
operators or pedestrians in the public right-of-way.
B.
The sign face of internally illuminated signs must function as a
filter to diffuse illumination. The sign face must cover all internal
illumination components so that no exposed bulbs are visible.
C.
All external illumination of a sign must concentrate the illumination
upon the printed area of the sign face.
D.
The use of bare bulbs as external illumination is only permitted
for marquee signs.
E.
No sign illumination may be combined with reflective materials, such
as mirrors, polished metal, or highly-glazed tiles, which would increase
glare.
F.
The maximum allowable foot-candle at the lot line is one foot-candle
unless such signs are allowed to extend over the lot line, where the
maximum of one foot-candle is measured at the back of curb or edge
of pavement.
G.
For electronic message signs, the maximum brightness is limited to
5,000 nits when measured from the sign's face at its maximum brightness,
during daylight hours, and 500 nits when measured from the sign's
face at its maximum brightness between dusk and dawn, i.e., the time
of day between sunrise and sunset. The sign must have an ambient light
meter and automatic or manual dimmer control that produces a distinct
illumination change from a higher allowed illumination level to a
lower allowed level for the time period between one-half hour before
sunset and one-half hour after sunrise.
All signs not expressly permitted by this ordinance are prohibited.
In addition, the following sign types are specifically prohibited.
A.
Banners wrapped around a permanent sign structure, such as a freestanding
sign or projecting sign.
B.
Balloon signs. Inflatable advertising displays designed to inflate
or move by use of a fan or blower are considered a balloon sign.
C.
Feather Flags/Sails.
D.
Flashing signs.
E.
Moving signs, including any sign that rotates, revolves, or has any
visible moving part, or any sign that gives the appearance of movement,
including signs designed to be moved by wind or other natural elements.
This excludes clocks and barber poles.
F.
Off-premise commercial signs — temporary. (Also known as push
signs or snipe signs.)
G.
Portable reader-board signs.
H.
Roof signs. This prohibition does not apply in the C-D District,
where roof signs are allowed.
I.
Strobe lights, moving or fixed spotlights, floodlights/searchlights.
J.
Signs that constitute a traffic hazard, including signs that:
1.
Interfere with, obstruct the view of, or may be confused with
any authorized traffic sign, signal, or device because of its position,
shape, or color, including signs illuminated in red, green, or amber
color designed to resemble a traffic signal.
2.
May be confused with any public safety lighting, including signs
illuminated in red and blue colors.
3.
Make use of the words STOP, LOOK, DETOUR, DANGER, CAUTION, WARNING,
or any other word, phrase, symbol, or character in a manner used to
direct traffic that would mislead, interfere with, or confuse traffic.
K.
Signs placed, mounted, installed, or painted on a vehicle for the
primary purpose of attracting attention to an occupant's presence
within a building at which the vehicle is being parked. This prohibition
does not include signs painted on or applied to vehicles, trucks,
or buses that are being operated and stored in the normal course of
business, such as signs located on delivery trucks, moving vans, and
rental trucks, provided that the primary purpose of such vehicles
is not the display of such sign, and that they are properly parked
or stored in areas related to their use as vehicles and all such vehicles
are in operable condition. Vehicle for-sale signs are exempt from
this provision.
L.
Video display signs.
A.
Alteration and Maintenance on Existing Signs. The following activities
are exempt from requiring a sign permit:
1.
Painting, cleaning, or other normal maintenance and repair of
a sign, not involving structural changes, or changes in the electrical
components of the sign, including the removal and replacement of electrical
components. Any activity that increases the sign area, sign height,
or any sign dimension, or moves the location of a sign, requires a
sign permit. The changing of a sign face requires a sign permit.
2.
Changing the copy of a changeable message sign or electronic
message sign.
B.
Ancillary Signs.
1.
Logos and labels located on mechanical equipment, recycling
bins, trash containers, and the like, which are part of the equipment
as manufactured and/or installed, are exempt.
2.
A maximum of one sign mounted on each gas station pump island
is permitted and is limited to 1.5 square feet in sign area. All such
signs must be oriented to face the vehicle fueling. Such signs may
be electronic but must meet the following standards:
C.
Permanent and Temporary Signs.
1.
A-Frame Sign.
a.
A-frame signs are permitted in the C-1, C-2, C-3, C-D, C-V,
and I-MU Districts.
b.
One A-frame sign is permitted per establishment, including one
for each tenant in a multi-tenant development. A minimum fifteen foot
separation is required between all A-frame signs.
c.
An A-frame sign must be placed within 15 feet of the primary
entrance of the business, and must not interfere with pedestrian traffic
or violate standards of accessibility as required by the ADA or other
accessibility codes.
d.
A-frame signs may be placed in the sidewalk or parkway concurrent
with the lot of the establishment being advertised and must comply
with all provisions of Chapter 12.36 of the Davenport Municipal Code.
e.
A-frame signs are limited to six square feet in area per side
and four feet in height.
f.
The placement of A-frame signs outdoors is limited to business
hours only. A-frame signs must be stored indoors at all other times.
g.
A-frame signs must not be used outdoors when high winds or heavy
rain conditions exist.
h.
Illumination of A-frame signs is prohibited.
i.
No A-frame sign may have any type of electronic component.
|
A-FRAME SIGN
 |
2.
Attention-Getting Devices. Attention-getting devices are signs,
devices, or ornamentations designed for the purpose of attracting
attention or promoting on-site goods or services. Attention getting
devices include banners, and temporary on-premise pole signs. Federal,
state, or local flags, or flags of fraternal, religious, and civic
organizations, and temporary holiday decorations are not considered
attention-getting devices.
a.
Attention-getting devices are permitted for nonresidential uses.
b.
Each establishment may have one freestanding and one wall-mounted
attention-getting device installed or mounted simultaneously.
c.
Attention-getting devices are limited to the following display
periods:
i.
When the attention-getting device advertises an event that has
a specific start and end time: A total display period of 30 days prior
to the start of the event, the time period of the event, and three
days following the end of the event.
ii.
All other attention-getting device advertises (non-time specific):
21 days.
iii.
A maximum of two display periods per year per
establishment is permitted with a minimum of 30 days between displays.
d.
Attention-getting devices for multi-tenant sites are subject
to the following rules:
e.
Freestanding attention-getting devices are subject to the following:
i.
One freestanding attention-getting device is allowed for every
75 feet of street frontage. There must be a fifteen foot separation
between freestanding attention-getting devices.
ii.
Freestanding attention-getting devices are limited to a maximum
height of six feet and 32 square feet in area.
iii.
All freestanding attention-getting devices must
be located a minimum of five feet from a lot line, as measured from
the outermost portion of the sign.
f.
Wall-mounted attention-getting devices are limited to 32 square
feet.
|
ATTENTION-GETTING DEVICES
  |
3.
Construction Activity Sign. On a lot where active construction
is taking place, one temporary sign is permitted per each street frontage.
Such temporary signs are subject to the following:
a.
Such temporary signs are permitted in all districts on sites
with active construction projects.
b.
Such temporary signs may be installed only after approval of
a building permit for such activity. Signs must be removed once construction
is complete or the building permit expires, whichever occurs first.
c.
Such temporary signs may be constructed as either freestanding
signs, wall signs, or installed on fences, and subject to the following:
4.
Government Sign. Federal, state, or local governments or taxing
bodies may install signs in the public interest in any number, configuration,
or size in any district or in the right-of-way. Such signs may be
illuminated as required by the agency. Temporary roadway work, utility
work, or emergency information signs may be electronic message signs.
5.
Light Pole Banner. Light pole banners on private property are
allowed as follows:
a.
Light pole banners are permitted for light poles on private
property and must be mounted so that they are held taut between support
posts.
b.
Light pole banners are limited to a maximum area of 15 square
feet.
c.
Light pole banners must be mounted to project perpendicular
from light poles.
d.
Light pole banners must not be used as a temporary off-premise
sign.
e.
Light pole banners must be mounted at least eight feet above
grade.
6.
Memorial or Historic Event. Commemoration of a historic person,
event, structure, or site allows one additional permanent sign as
follows:
a.
Such signs are permitted in any district.
b.
Such signs may be constructed as either freestanding or wall
signs, subject to the following:
i.
Signs are limited to six square feet.
ii.
Signs are limited to four feet in height.
iii.
Signs must be located five feet from any lot line.
iv.
Wall mounted signs must be inlaid so as to be an integral part
of the structure, cut into stone or masonry, or be a permanently affixed
plaque of bronze or aluminum.
v.
Signs may be externally illuminated.
c.
Such signs are limited to one per street frontage, which may
be inlaid into the facade associated with that street frontage.
7.
Multiple Tenant Building Entryway. Multiple tenant buildings,
such as multi-family dwellings and non-residential developments with
multiple tenants, are permitted a permanent sign for the entryway
subject to the following.
a.
Signs may be constructed as either freestanding or wall signs,
subject to the following:
i.
Signs are limited to six square feet in area.
ii.
Freestanding signs are limited to five feet in height, and must
be located within five feet of the building entry and a minimum of
five feet from any lot line.
iii.
Freestanding signs must be installed so that they
are primarily viewable from the building entryway and not intended
to be viewed from a public right-of-way.
iv.
Signs may only be internally illuminated.
b.
Signs are limited to one per building entry.
8.
Noncommercial Message. Signs used for the expression of noncommercial
ideas and messages are permitted in all districts. Examples include
but are not limited to signs advocating a public issue, recommending
a candidate for public office, alerts, or warnings.
a.
Noncommercial message signs may be constructed as either freestanding,
wall, or window signs, or mounted on fences. There is no limit on
the number of signs permitted.
b.
Freestanding and wall/fence-mounted noncommercial message signs
are limited to 32 square feet in area. Freestanding noncommercial
message signs are limited to six feet in height.
c.
Window-mounted noncommercial message signs must meet the coverage
limitations of window signs. If no coverage is specified, the limitation
is 30% of the window area.
d.
Freestanding noncommercial message signs must be located five
feet from any lot line.
e.
Noncommercial message signs posted on private property must
have the permission of the property owner.
f.
Noncommercial message signs cannot be illuminated.
g.
Noncommercial message signs cannot be used as a temporary off-premise
sign.
9.
Parking Lots and Structures: Additional Signs. Parking lots
and structures are permitted additional signs, whether such parking
lots or structures are a principal or ancillary use.
a.
An additional sign is permitted at each entrance/exit, driveway
intersection, drive-through lane, and other circulation points.
b.
Signs are limited to the following maximum dimensions: two feet
in length and two feet in height.
c.
A freestanding sign is limited to five feet in height and must
be five feet from any lot line that abuts a street.
d.
Signs located at an entrance/exit, driveway intersection, drive-through
lane, and other circulation points may be internally illuminated.
10.
Real Estate Activity. When a structure or lot is offered for
sale, lease, or rent, such lot is permitted an additional temporary
sign as follows:
a.
Such signs are permitted in all districts. Signs must be located
on the site of the property for sale, lease, or rent.
b.
Signs are limited to one per street frontage.
c.
Signs may be constructed as either freestanding, wall, or window
signs.
d.
Signs are limited to 12 square feet in residential districts
and 32 square feet in all other districts.
e.
Freestanding signs are limited to six feet in height and must
be located within five feet from any lot line.
f.
Such signs may not be illuminated.
g.
Signs must be removed within five days of final closing, lease,
or rental. If such signs are used in conjunction with a promotional
activity related to the sale, lease or rent, such signs may be installed
48 hours prior to event and must be removed within 24 hours of the
end of the event
11.
Window Sign.
a.
Window signs are permitted for all nonresidential uses in all
districts.
b.
All window signs, whether temporary or permanent, are limited
to no more than 30% of the surface of each window area. Window area
is counted as a continuous surface until divided by an architectural
or structural element. Mullions are not considered an element that
divides window area.
c.
Window signs include neon or LED signs. Flashing neon or LED
is prohibited.
|
WINDOW SIGN
 |
This section describes the types of signs allowed with a sign
permit. Specific regulations on each sign type may include further
restrictions on which districts and/or uses within a district may
utilize these sign types. Signs must also comply with all provisions
of Chapter 12.36 of the Davenport Municipal Code
A.
Awning Sign.
1.
Awning signs are permitted for multi-family dwellings and nonresidential
uses in any district.
2.
Awning signs must maintain a minimum vertical clearance of eight
feet.
3.
Awning signs may encroach into the public right-of-way but can
only encroach a maximum of 2/3 the distance from the lot line to the
back of curb.
4.
Awning signs must be made of a durable, weather-resistant material
such as canvas, canvas-like material, nylon, vinyl-coated fabric,
or permanent building material such as metal.
5.
Sign copy on any awning sign surface is limited to 25% of each
surface area. A valance is considered a separate surface area.
6.
Solid awnings are permitted lettering attached to and located
above the top of the awning to a maximum height of 18 inches.
7.
Awning signs may be externally illuminated and lighting must
be focused on the printed area.
8.
Back-lit awnings are prohibited.
|
AWNING SIGN
 |
B.
Canopy Sign. Canopy signs are divided into two types: non-structural
and structural.
1.
Non-Structural Canopy Signs.
a.
Non-structural canopy signs are permitted for multi-family dwellings
and nonresidential uses in all districts.
b.
Non-structural canopy signs must maintain a minimum vertical
clearance of eight feet.
c.
Non-structural canopy signs may encroach into the public right-of-way
but can only encroach a maximum of 2/3 the distance from the lot line
to the back of curb Support posts must maintain a minimum separation
of five feet between posts and five feet between the posts and any
building wall.
d.
Non-structural canopy signs must be made of a durable, weather-resistant
material such as canvas, canvas-like material, nylon, or vinyl-coated
fabric.
e.
Sign copy on any canopy sign surface is limited to 25% of each
surface area.
f.
Non-structural canopy signs may be externally illuminated and
lighting must be focused on the printed area.
g.
Back-lit canopies are prohibited.
2.
Structural Canopy Signs.
a.
Permissions for Structural Canopy Signs. Structural canopy signs
are permitted as follows:
b.
Structural Canopy Signs Attached to Principal Structure Structural
canopy signs attached to the principal structure are subject to the
following:
i.
Structural canopy signs attached to the principal structure
may encroach into the public right-of-way but can only encroach a
maximum of 2/3 the distance from the lot line to the back of curb.
ii.
Support posts must maintain a minimum separation of five feet
between posts and five feet between the posts and any building wall.
iii.
Structural canopy signs attached to a building
must maintain a minimum vertical clearance of eight feet.
iv.
For structural canopies attached to a principal building, sign
copy is limited to 25% of each surface area. Such signs are permitted
lettering attached to and located above the top of a structural canopy
to a maximum height of 18 inches.
v.
Structural canopy signs attached to the principal structure
must be made of permanent building material, such as metal or brick.
vi.
Structural canopy signs may be internally or externally illuminated.
If externally illuminated, the lighting must be focused on the sign.
c.
Freestanding Structural Canopy Signs. Freestanding structural
canopy signs are subject to the following:
i.
Freestanding structural canopy signs are subject to the setback
requirements of the district where they are located or 10 feet from
a lot line, whichever is greater.
ii.
Freestanding structural canopy signs are limited to a maximum
height of 25 feet. Height is measured to the top of a flat roof or
in the case of a pitched roof to the mean between the eaves and peak.
iii.
For freestanding structural canopies, sign copy
is limited to a maximum of 25% of the area of each facade. No sign
may be mounted above the top of the roof of the structural canopy,
but a sign mounted on the structural canopy facade may extend a maximum
of six inches above the roofline.
iv.
Freestanding structural canopy signs must be made of permanent
building material.
v.
Freestanding structural canopy signs may be internally or externally
illuminated. If externally illuminated, the lighting must be focused
on the sign. Freestanding structural canopies are permitted an illuminated
band along each facade of the canopy, which is limited to 10% of the
overall height of the facade of the canopy.
|
CANOPY SIGN: NON-STRUCTURAL
 |
|
CANOPY SIGN: STRUCTURAL — ATTACHED
 |
|
CANOPY SIGN: STRUCTURAL — FREESTANDING
 |
C.
Electronic Message Sign.
1.
Electronic message signs are permitted as follows:
a.
In commercial and industrial districts.
b.
In the S-IC District.
c.
The following uses in any district: conservation area, cultural
facility, educational facility - primary or secondary, educational
facility - university or college, government office/facility, park/playground,
places of worship.
d.
Gas stations in any district are permitted an electronic message
sign to display copy graphic that is required to be displayed by law,
such as fuel prices.
2.
Electronic message signs located within or adjacent to a residential
district must be turned off between the hours of 11:00 p.m. and 7:00
a.m. The Zoning Administrator may restrict or expand these hours as
part of the sign permit based on the times the use is open to the
public.
3.
Electronic message signs are permitted as part of a freestanding,
marquee, or projecting sign, and are subject to the requirements for
that sign type within the district.
4.
Electronic message signs must be integrated into the design
of the larger sign structure. The electronic component is limited
to a maximum of 70% of the total area of a sign. The larger sign structure
must contain additional copy; it cannot be a blank sign structure
once the electronic message sign component is discounted.
5.
Only one electronic message sign per lot is permitted. For the
purposes of this regulation, a multi-tenant development where the
development as a whole is comprised of separate lots of record, the
entire development, including outlot parcels and inline development,
is considered one lot.
6.
Each message or image displayed on an electronic message sign
must be static for a minimum of two seconds plus one second for transition
of messages; such transition may include scrolling, fading in, dropping
in, or similar moving copy changes. Multi-color messages and static
images are permitted.
7.
Electronic message signs cannot operate as a commercial off-premise
sign. This does not include public service messages.
8.
Video display screens are prohibited.
|
ELECTRONIC MESSAGE SIGN
 |
D.
Freestanding Sign.
1.
Freestanding Sign Types. Freestanding signs are regulated as
three types in this ordinance:
[Amended 6-10-2020 by Ord. No. 2020-233]
a.
Freestanding signs – standard are permitted for multifamily
dwellings and nonresidential uses (includes a nonresidential use comprised
of two commercial establishments sharing a common building or which
are in separate buildings that share a common access/entranceway or
parking area) in any district.
b.
Freestanding signs – multitenant commercial center are
permitted for multitenant commercial centers in any district. A multitenant
commercial center is a commercial development under unified control
consisting of three or more separate commercial establishments sharing
a common building, or which are in separate buildings that share a
common access/entranceway or parking area.
c.
Freestanding signs – residential subdivision are permitted
for residential subdivisions in any district.
2.
General Regulations. The following regulations apply to all
types of freestanding signs:
a.
Freestanding signs must be of monument construction in all districts
except the I-1 and I-2 Districts. Monument or pole sign construction
is allowed the I-1 and I-2 Districts. Such sign types are defined
as follows:
i.
Freestanding monument sign: A sign that is placed on or supported
by the ground, independent of a structure on the lot, designed with
a monument base that is an integral part of the sign structure. A
freestanding monument sign must be designed so that the width of the
top of the sign face is a minimum of 70% and a maximum of 130% of
the width of the base, unless designed with decorative posts as follows:
(A)
In order to create flexibility for monument signs
installed where the ground is not level, structural (non-decorative)
posts may extend out of the ground but are limited to a maximum of
six inches above the adjacent ground where they are installed.
(B)
A monument sign may be designed with decorative
posts that are part of the overall sign structure and sign design.
Such decorative posts may extend out of the ground for a maximum of
three feet above the adjacent ground where they are installed.
|
MONUMENT SIGN
 |
ii.
Freestanding pole sign: A type of freestanding sign that is
affixed, attached, or erected on one or more poles, uprights, or braces
from the ground and not supported by a building. Pole signs are any
freestanding signs that do not meet the design and construction standards
of this ordinance for a monument sign. Permitted attention getting
devices or other freestanding temporary signs are regulated separately
by this ordinance.
b.
Freestanding signs must be set back a minimum of five feet from
any lot line. No freestanding sign may project into, over, or otherwise
encroach on a public right-of-way or public easement.
c.
Freestanding signs may be internally or externally illuminated.
If externally illuminated, all light must be directed onto the sign
face.
d.
Freestanding signs must be constructed of brick, wood or simulated
wood, stone, concrete, metal, plastic, or high-density urethane (HDU)
foam board or similar durable foam construction.
e.
All freestanding signs must be landscaped at the base of the
sign as follows:
i.
Landscape must extend a minimum of two feet from the sign base
on all sides with small shrubs a minimum of 18 inches in height at
planting in a single row around the perimeter of the sign base. The
remainder of the required landscape area must be planted with trees,
perennials, or other live ground cover.
ii.
If a sign is designed with a decorative base and such decorative
base extends to the ground, the single row of shrubs around the perimeter
of the sign base is not required. Landscape must extend a minimum
of two feet from the sign base around a minimum of 50% of the perimeter
of the sign base, and must be planted with shrubs, trees, perennials,
or other live ground cover.
iii.
If landscape is required on a site, ground sign
landscape is included in the total amount of landscape required on
a site. Where a sign is installed in any landscape area of a site,
the specific landscape requirements of this section do not apply and
the sign landscape must be integrated into the overall site landscape
plan. Sign landscape must be shown on the landscape plan.
iv.
All landscape must be maintained in good condition, and free
and clear of rubbish and weeds.
3.
Freestanding Signs - Standard Regulations. Freestanding signs
- standard are subject to the following.
a.
One freestanding sign - standard is permitted per lot.
b.
Freestanding sign - standard are limited to a maximum area of
100 square feet.
c.
Freestanding sign - standard are limited to a maximum height
of 10 feet in the residential districts, and in the C-T, C-l, C-D,
C-V, and S-AG Districts. In all other districts where allowed they
are limited to 25 feet.
4.
Freestanding Signs – Multitenant Commercial Regulations.
Freestanding signs – multitenant commercial center are subject
to the following.
a.
One freestanding sign – multitenant commercial center
is permitted per street frontage of a lot. An additional freestanding
sign is permitted for each additional access point to the lot; however,
a minimum separation of 75 feet is required between signs. For the
purposes of this regulation, a multitenant development where the development
as a whole is comprised of separate lots of record, the entire development,
including outlot parcels and inline development, is considered one
lot.
5.
Freestanding Signs - Residential Subdivision Regulations. Freestanding
signs - residential subdivision are subject to the following sign
area, sign height, and sign number permissions.
a.
One freestanding sign - residential subdivision is permitted
for each entry point to the development. A minimum separation of 100
feet is required between signs.
b.
Freestanding signs - residential subdivision are permitted a
maximum sign area of 100 square feet per sign and a maximum sign height
of 10 feet per sign.
E.
Marquee.
1.
Marquees are permitted for commercial uses in C-3, C-D, and
C-V Districts.
2.
Marquees must be supported solely by the building to which they
are attached. No exterior columns or posts are permitted as supports.
3.
The roof of a marquee may not be used for any purpose other
than to form and constitute a roof and must be constructed of noncombustible
material.
4.
Water from the roofs of a marquee may not drain, drip, or flow
onto the surface of a public right-of-way. Sufficient downspouts,
drains, and gutters must be installed as part of each marquee to prevent
water from the roof of the marquee from flowing onto the surface of
a public right-of-way.
5.
Marquees must be erected over a building entrance and are limited
to the width of the building entrance plus an additional five feet
on each side of the entrance doors covered by the marquee.
6.
All marquees must maintain a minimum vertical clearance of eight
feet, and the roof of the marquee structure must be erected below
the second floor windowsill, and must not conceal any significant
architectural features or ornamentation of the building.
7.
Marquees may encroach into the public right-of-way but must
be located at least two feet from the curb line.
8.
Marquees are permitted lettering attached to and located above
the roof of a marquee to a maximum height of 48 inches.
9.
Marquees are permitted an electronic message component if the
district allows electronic message signs. Marquees are also permitted
a changeable message board as part of the marquee structure. However,
the marquee may only have either a changeable message board sign or
an electronic message sign.
10.
Marquees may be internally illuminated. Marquee bare-bulb illumination
is permitted.
|
MARQUEE
 |
F.
Menu board.
1.
Menu boards are permitted for all drive-through facilities in
any district.
2.
Menu boards are limited to a maximum of two per drive-through
lane.
3.
Menu boards are limited to 80 square feet in sign area and eight
feet in height. The menu board may be designed as separate freestanding
signs grouped together and may include the use of preview boards designed
as separate freestanding signs installed a distance earlier in the
drive-through lane, however the total area of all signs must not exceed
80 square feet.
4.
Menu boards are permitted an additional 10 square feet of sign
area for temporary signs attached to the top or sides of the menu
board.
5.
Menu boards must be located a minimum of 15 feet from any residential
district lot line. This is measured from sign face to lot line, including
any public right-of-way.
6.
Menu boards may be internally illuminated. Menu boards may also
contain an electronic screen for interaction with each customer.
|
MENU BOARD
 |
G.
Projecting Signs.
1.
Projecting signs are permitted in the commercial districts and
the I-MU District.
2.
Projecting signs in the C-T, C-l, and C-V Districts are limited
to 12 square feet. Projecting signs in all other districts where allowed
are limited to 24 square feet.
3.
One projecting sign is permitted per establishment with frontage
on a street. For a corner lot, one projecting sign is permitted for
each street frontage.
4.
Projecting signs may encroach into the public right-of-way but
can only encroach a maximum of 2/3 the distance from the lot line
to the back of curb or four feet from the building facade, whichever
is less.
5.
Projecting signs must maintain a minimum vertical clearance
of eight feet. No projecting sign affixed to a building may project
higher than the building height, including the sign support structure.
6.
Projecting signs must be constructed of wood or simulated wood,
metal, durable, weather-resistant material like canvas, canvas-like
material, nylon or vinyl-coated fabric, plastic, or high-density urethane
(HDU) foam board or similar durable foam construction. Projecting
signs constructed of canvas or similar material must be mounted so
that they are held taut between support posts.
7.
Projecting signs may be internally or externally illuminated.
If externally illuminated, all lighting must be directed onto the
sign face from above.
|
PROJECTING SIGN
 |
H.
Roof Sign.
1.
Roof signs are permitted only in the C-D District. They are
prohibited in all other districts.
2.
Roof signs are limited to a maximum width of 75% of the roof
width (measured along the facade the sign is mounted parallel to)
and a maximum height of 15 feet (measured from the roof to the uppermost
point of the sign).
3.
A maximum of one roof sign is permitted per building.
4.
A roof sign may be installed only on a flat roof.
5.
A roof sign must be set back at least three feet from the outermost
walls of the roof.
6.
Roof signs must be safely and securely attached to the roof
structure and must not interfere with any roof access points.
|
ROOF SIGN
 |
I.
Wall Sign.
[Amended 6-10-2020 by Ord. No. 2020-233]
1.
Wall signs are permitted for all nonresidential uses in any
district.
2.
Wall signs are permitted on all facades of a structure. On a
site consisting of multiple structures, each structure is permitted
wall signs per the regulations of this section. The square footage
from different structures cannot be combined to create a larger sign
on any one structure.
3.
For a single tenant structure, the maximum total wall sign area
is two square feet per linear foot of building wall where the wall
sign(s) will be mounted or 80 square feet, whichever is greater. The
square footage from different facades cannot be combined to create
a larger sign on any one facade.
4.
For a structure that contains multiple tenants, each tenant
that has exterior business facade area is permitted a total wall sign
area of two square feet per linear foot of business frontage or 80
square feet, whichever is greater, along their individual frontage(s).
5.
The number of individual wall signs on a facade is not limited;
however, the cumulative sign area of all signs on a facade cannot
exceed the maximum allowable total wall sign area per facade.
6.
Wall signs may be internally or externally illuminated. If externally
illuminated, all light must be directed onto the sign face.
7.
Wall signs must be safely and securely attached to the building
wall. Wall signs must project 18 inches or less from the building
wall. Wall signs may encroach into the public right-of-way no more
than 18 inches.
8.
No wall sign affixed to a building, including sign support structure,
may project beyond the ends or top of the wall or higher than the
roofline of the structure to which it is attached.
9.
Wall signs must be constructed of wood or simulated wood, metal,
plastic, or high-density urethane (HDU) foam board or similar durable
foam construction. Canvas and similar material wall signs and painted
wall signs are prohibited.
10.
Wall signs are permitted on architectural appurtenances, such
as chimneys or penthouses, which are part of the structure. Wall signs
must not cover any window, windowsill, transom sill, or significant
architectural feature of the structure.
11.
On existing buildings, a parapet wall must not be constructed
for the sole purpose of increasing the allowable height of a wall
sign. For new buildings, when a sign is mounted on a parapet wall,
that parapet wall must be consistent with the architectural design
of the building, including building materials.
12.
Signs may be projected onto a wall and do not count toward total
wall sign area. Such signs must remain static and cannot flash, rotate,
or move. No such projected wall sign can project an electronic video.
No such projected sign may glare onto adjacent properties.
[6-10-2020 by Ord. No. 2020-233]
Table 17.12-1: Summary of Sign Permissions catalogs the types
of permitted signs, both permanent and temporary, and indicates whether
such sign requires a sign permit. This table is provided for reference
purposes. In the case of any conflict with the regulations of this
chapter and this ordinance, the specific sign regulations control
over this table. All signs must comply with all provisions of Chapter
12.36 of the Davenport Municipal Code.
|
Table 17.12-1: Summary of Sign Permissions
| |||
|---|---|---|---|
|
Sign Type
|
Exempt Sign
(Section 17.12.050)
|
Permit Required
(Section 17.12.060)
|
Permitted Locations
|
|
A-Frame Sign
|
•
|
C-1, C-2, C-3, C-D, C-V, and I-MU Districts
| |
|
Attention-Getting Device
|
•
|
Nonresidential uses
| |
|
Awning Sign
|
•
|
Multifamily dwellings and nonresidential uses in all districts
| |
|
Canopy Sign: Nonstructural Canopy Signs
|
•
|
Multifamily dwellings and nonresidential uses in all districts
| |
|
Canopy Sign Structural: Attached to Principal Building
|
•
|
Multifamily dwellings and nonresidential uses in all districts
| |
|
Canopy Sign Structural: Freestanding
|
•
|
Gas stations and drive-through facilities in any district
| |
|
Construction Activity Sign
|
•
|
On a lot where active construction is taking place in all districts
| |
|
Electronic Message Sign
|
•
|
Commercial and industrial districts S-IC District
Following uses in any district: conservation area, cultural
facility, educational facility - primary or secondary, educational
facility - university or college, government office/facility, public
park, places of worship
Gas stations in any district
| |
|
Freestanding Signs - Standard
|
•
|
Multifamily dwellings and nonresidential uses in all districts
| |
|
Freestanding Signs - Multitenant Commercial Center
|
•
|
Multitenant commercial centers in all districts
| |
|
Freestanding Signs - Residential Subdivision
|
•
|
Residential subdivisions in all districts
| |
|
Government Sign
|
•
|
All districts
| |
|
Light Pole Banner
|
•
|
Light pole banners on private property in all districts
| |
|
Marquee
|
•
|
Commercial uses in C-3, C-D, and C-V Districts
| |
|
Memorial or Historic Event
|
•
|
Where a structure or lot is related to an historic person, event,
structure, or site in all districts
| |
|
Menu Board
|
•
|
Drive-through facilities in all districts
| |
|
Multiple-Tenant Building Entryway
|
•
|
Entryways for multiple-tenant buildings (multifamily dwellings
and nonresidential and mixed-use developments) in all districts
| |
|
Noncommercial Message
|
•
|
All districts
| |
|
Parking Lots and Structures
|
•
|
Parking lot/structures for each entrance/exit, driveway intersection,
drive-through lane, and other circulation points in all districts
| |
|
Projecting Signs
|
•
|
Commercial districts
| |
|
Real Estate Activity
|
•
|
When a structure or lot is offered for sale, lease, or rent
in all districts
| |
|
Roof Sign
|
•
|
C-D District
| |
|
Wall Sign
|
•
|
Nonresidential uses in all districts
| |
|
Window Sign
|
•
|
Nonresidential uses
| |
A.
In the S-IC District, educational facilities and hospital campuses
have unique sign needs that may need to depart from the requirements
of this chapter. In such cases, the Zoning Administrator may approve
such sign standards for temporary and permanent signs through the
approval of a Sign Master Plan. The Sign Master Plan must be submitted
and approved in conjunction with a sign permit.
B.
A Master Sign Plan may be applied for by an educational facility
or hospital campuses in the S-IC District a minimum of two acres in
size. In calculating the area, the entire area does not have to be
contiguous and may be separated by rights-of-way or by individual
parcels not owned by the institution. However, the entire area must
function as a connected campus.
C.
A comprehensive sign plan must be submitted to the Zoning Administrator.
The comprehensive sign plan must describe the planned signs for the
campus, including all exceptions to the requirements of this chapter.
The sign plan may be more permissive than the standards of this section.
Directional signs within the campus may be described generally by
sign area and height, and general locations.
D.
In no case may a Master Sign Plan allow for off-premise signs.
