The following is a list of acceptable manufacturers:
A. 
Restrained joint pipe:
(1) 
Push-on joint pipe:
(a) 
American Pipe, Flex-Ring, or Lok-Ring.
(b) 
US Pipe - TR Flex.
(c) 
Or equal.
(2) 
Rigid restrained mechanical joint pipe:
(a) 
American Pipe, Flex-Ring, or Lok-Ring.
(b) 
US Pipe - TR Flex.
(c) 
Or equal.
(3) 
Mechanical joint restraint system:
(a) 
EBAA, Iron Inc., Megalug.
(b) 
Or equal.
B. 
Gravity sewer line:
[Added 10-22-2015 by Res. No. 15-10-003[1]]
(1) 
PVC SDR 35 pipe:
(a) 
JM Eagle (J-M Manufacturing Company, Inc.).
(b) 
Charlotte Pipe and Foundry Company.
(c) 
North American Pipe Corporation.
(d) 
Or approved equal.
[1]
Editor's Note: Pursuant to this resolution, former Subsections B through BB were redesignated as Subsections D through DD, respectively.
C. 
Low-pressure force main:
[Added 10-22-2015 by Res. No. 15-10-003]
(1) 
High-density polyethylene (HDPE):
(a) 
JM Eagle (J-M Manufacturing Company Inc.).
(b) 
Georg Fischer Central Plastics.
(c) 
Or approved equal.
D. 
Saddles:
(1) 
Romac.
(2) 
General Engineering Co.
(3) 
Or approved equal.
E. 
Cross for inside drop manhole:
(1) 
GPK.
(2) 
Or approved equal.
F. 
Flexible pipe couplings:
(1) 
Fernco Joint Sealer Co.
(2) 
Or approved equal.
G. 
Mechanical joint couplings:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
Dresser.
(2) 
Smith-Blair.
(3) 
Or approved equal.
H. 
Utility warning tape:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
Reef Industries; Terra Tape Sentry Line Detectable.
(2) 
Or approved equal.
I. 
Preformed butyl rubber sealing compound:
(1) 
Conseal CS102.CS202.
(2) 
Henry Sealant Division; Rub-R-Nek.
(3) 
Press-Seal Gasket Corp.; EX-Stik.
(4) 
Or approved equal.
J. 
Grout, nonshrink, nonmetallic:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
Sonneborn; Sonogrout.
(2) 
Master Builders; Masterflow 713.
(3) 
U.S. Grout Corp.; Five Star.
(4) 
Or approved equal.
K. 
Manhole frame and cover:
(1) 
Neenah Foundry Company.
(2) 
Bridgestate Foundry.
(3) 
East Jordan Iron Works.
(4) 
Or approved equal.
L. 
Manhole frame and cover hold down bolts and inserts:
(1) 
Hilti.
(2) 
A-Lok Bolt Slot Insert.
(3) 
Or approved equal.
M. 
Manhole steps:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
Aluminum:
(a) 
Neenah Foundry R-1982W Extruded.
(b) 
Or approved equal.
(2) 
Reinforced plastic:
(a) 
M.A. Industries.
(b) 
Lane Manhole Steps.
(c) 
Or approved equal.
N. 
Manhole insert:
(1) 
Parson Environmental Products, Inc.
(2) 
Or approved equal.
O. 
Waterproofing coatings for concrete structures and manhole exteriors:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
Sherwin Williams Hi-Mil Sher-Tar Epoxy, 20 mils minimum thickness.
(2) 
Cooper Black No. 760 top Service Black, 20 mils minimum thickness.
(3) 
Or approved equal.
P. 
Corrosion-resistant coating for manhole interior:
(1) 
Spray Wall from Sprayroq, Inc.
(2) 
Or approved equal.
Q. 
Pipe opening seals for manholes:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
Press-Seal Gasket Corp: PSX Series.
(2) 
A-LOK Products: A LOK Manhole Pipe Seal.
(3) 
Or approved equal.
R. 
Mechanical seals:
(1) 
Thunderline Corp.
(2) 
Link-Seal.
(3) 
Or approved equal.
S. 
Expandable sleeve and boot seals:
(1) 
Press Seal PSX.
(2) 
Kor-N-Seal.
(3) 
Or approved equal.
T. 
Thermoplastic manhole liner:
(1) 
A-Lok Products, Inc.; Dura Plate 100.
(2) 
Ameron Protective Linings; T-Lock PVC Liner.
(3) 
Or approved equal.
U. 
Manhole protection post coating:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
Sherwin Williams DuraPlate 235 multipurpose epoxy.
(2) 
Or approved equal.
V. 
Sewage air release valve:
(1) 
GA Industries, Inc. Figure 929-F.
(2) 
Val-Matic Valve & Manufacturing Corp.; Model 48 BWA.
(3) 
Or approved equal.
W. 
Sewage air and vacuum valve:
(1) 
GA Industries, Inc. Figure 939-F.
(2) 
Val-Matic Valve & Manufacturing Corp.; Model 300 Series.
(3) 
Or approved equal.
X. 
Sewage combination air valve:
(1) 
GA Industries, Inc. Figure 942-F.
(2) 
Val-Matic Valve & Manufacturing Corp.; Model 48 or 49/300 Series.
(3) 
Or approved equal.
Y. 
Casing spacers and end seals:
(1) 
Advance Products and Systems, Inc.
(2) 
Cascade Waterworks Mfg.
(3) 
Or approved equal.
Z. 
Individual grinder pumping stations:
[Amended 12-15-2011 by Res. No. 11-12-001]
(1) 
Environment One.
(2) 
Or approved equal.
AA. 
Service line check valve:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
Clean Check, Inc.: Rectorseal Extendable backwater valves.
(2) 
Or approved equal.
BB. 
Saddles (cast iron) for sewer laterals and service lines:
(1) 
Romac.
(2) 
General Engineering Co.
(3) 
Or approved equal.
CC. 
Saddles (PVC) for sewer laterals and service lines:
[Amended 10-22-2015 by Res. No. 15-10-003]
(1) 
JM Eagle: J-M Manufacturing Company Inc.
(2) 
Or approved equal.
DD. 
Flexible pipe couplings for sewer laterals and service lines:
(1) 
Fernco Joint Sealer Co.
(2) 
Or approved equal.
EE. 
Exterior grease interceptors:
[Added 10-22-2015 by Res. No. 15-10-003]
(1) 
Monarch Products Inc.
(2) 
Or approved equal.
FF. 
Tracer wire and accessories:
[Added 10-22-2015 by Res. No. 15-10-003]
(1) 
Copperhead Industries, LLC.
(2) 
Or approved equal.